Huawei FusionServer Pro 2288H V5 Скачать руководство пользователя страница 81

Страница: 81 / 177

Installation and Configuration

7.1 Installation Environment Requirements

7.2 Hardware Installation

7.3 Power-On and Power-Off

7.4 Initial Configuration

7.1 Installation Environment Requirements

7.1.1 Space and Airflow Requirements

To allow for servicing and adequate airflow, observe the following space and airflow
requirements:

Install the server in an access-restricted area.

Keep the area in which the server is located clean and tidy.

To facilitate heat dissipation and maintenance, keep a clearance of 800 mm (31.50 in.)
between walls and the front and rear doors of the cabinet.

Do not block the air intake vents. Otherwise, air intaking and heat dissipation will be
affected.

The air conditioning system in the equipment room provides enough wind to ensure
proper heat dissipation of all components.

FusionServer Pro 2288H V5 Server
User Guide

7 Installation and Configuration

Issue 08 (2019-10-30)

Содержание FusionServer Pro 2288H V5


















































































































































































Результаты поиска

Содержание FusionServer Pro 2288H V5

Отзывы:

Похожие инструкции для FusionServer Pro 2288H V5

Бренды по названию

Популярные бренды

Huawei FusionServer Pro 2288H V5, Руководство пользователя

Результаты поиска

Содержание FusionServer Pro 2288H V5

Отзывы:

Похожие инструкции для FusionServer Pro 2288H V5

Бренды по названию

Популярные бренды