Huawei eSpace IAD Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 109

background image

eSpace IAD
Troubleshooting

1 Overvie w

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

2

1

Overview

About This Chapter

This topic describes the fault severity, precautions, and troubleshooting process.

1.1 Fault Level

Depending on the impact and scope of the fault, faults are classified as either emergency
faults or ordinary faults.

1.2 Precautions

This topic describes the precautions for troubleshooting.

1.3 Troubleshooting Process

This topic describes the IAD troubleshooting process.

1.1 Fault Level

Depending on the impact and scope of the fault, faults are classified as either emergency
faults or ordinary faults.

Emergent faults refer to those that occur suddenly and affect a wide range of services or
devices. Emergency faults, such as host breakdown and service congestion, seriously affect
network operations and the quality of service (QoS).

The following faults are emergency faults:



IAD voice and fax services are unavailable.



The IAD restarts continuously.

Ordinary faults refer to those that are not emergency faults. The methods for locating and
rectifying faults and the applicable reference documents are different for emergency and
ordinary faults. For details, see

Table 1-1

Methods for locating and rectifying faults

Fault Level

Processing Method

Reference Document

Ordinary

Locate and rectify the fault.

See the description for this
document.

Emergency

Restore the service that has
been affected as soon as
possible, and then find the
root cause of the fault.

Contact Huawei technical
support for help.

«
...
5
6
7
8
9
...
»

Содержание eSpace IAD














































































































Отзывы:

Нет отзывов

Похожие инструкции для eSpace IAD

Бренд: iDance Страницы: 25

Бренд: HandyTrac Страницы: 14

RDS17S-ELITE1-R1

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: Discount Car Stereo Страницы: 5

Бренд: DAPAudio Страницы: 12

Бренд: Carel Страницы: 94

Бренд: auna multimedia Страницы: 26

Бренд: Hama Страницы: 53

Бренд: Elenberg Страницы: 36

Бренд: RF SOLUTIONS Страницы: 8

Бренд: Blaupunkt Страницы: 63

IRIDIUM CERTUS 100

Бренд: Lars Thrane Страницы: 4

Бренд: AMX Страницы: 1

Бренд: Yealink Страницы: 42

Бренд: Sharp Страницы: 4

Бренд: Sharp Страницы: 32

Бренд: Sharp Страницы: 48

Бренд: Sharp Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды