Huawei eSpace IAD Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 109

background image

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

55

Solution

Step 1

Ver ify that the correct power supply is used. The input voltage for the IAD208E(M) must be
12 V.

Step 2

Check whether the phone connected to the port is hung up.



If no, hang up the phone.



If yes, go to

Step 3

Check whether the splitter connected to the port is running properly.



If no, replace the splitter.



If yes, go to

Step 4

Check whether the user line connected to the port is normal.



If no, replace the user line.



If yes, go to

Step 5

Contact Huawei technical support.

----End

2.3.21 Two IADs on the Same VLAN Cannot Ping Each Other, and
the Phone Does Not Ring When a User Under One IAD Makes a
Call to Another User Under the Other IAD

Symptom

Two IADs on the the same VLAN cannot ping each other. When a user under one IAD makes
a call to another user under the other IAD, the phone does not ring.

Cause

The possible causes are as follows:



The network is disconnected.



The IAD configuration is incorrect.

Solution

Step 1

Check whether the network cable is connected properly.



If no, reconnect the network cable.



If yes, go to

Step 2

Check whether the configuration on the two IADs is correct. For details, see VLAN
configuration in the product document.



If yes, go to



If no, modify the configuration.

Step 3

Ver ify that the configuration on the upstream device connected to the two IADs is correct.

«
...
58
59
60
61
62
...
»

Содержание eSpace IAD














































































































Отзывы:

Нет отзывов

Похожие инструкции для eSpace IAD

Бренд: Safeline Страницы: 8

Бренд: Tait Страницы: 3

Бренд: elsner elektronik Страницы: 148

Бренд: Daewoo Страницы: 48

Бренд: Grundig Страницы: 16

Бренд: Leviton Страницы: 2

Бренд: Konftel Страницы: 8

AUDEMAT FM PROBE

Бренд: Worldcast Systems Страницы: 80

Бренд: AbleNet Страницы: 8

Бренд: Sonoro Страницы: 336

Бренд: Regintech Страницы: 82

Бренд: ETC Страницы: 386

Acendo Core ACR-5100

Бренд: AMX Страницы: 69

Бренд: Pioneer Страницы: 6

Бренд: Pioneer Страницы: 6

Бренд: Pioneer Страницы: 7

Бренд: Pioneer Страницы: 8

Бренд: Pioneer Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды