Huawei eSpace IAD Скачать руководство пользователя страница 59

Страница: 59 / 109

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

Solution

Step 1

Run the

display protocol

command on the IAD or choose

Advanced Configuration

Protocol Mode

to view the protocol mode. Check whether the protocol mode is correct.



If no, run the

protocol-mode

command or choose

Advanced Configuration

Protocol

Mode

to change the protocol mode.



If yes, go to

Step 2

Step 2

Check whether the softswitch can be pinged on the IAD.



If no, verify the network connection.



If yes, go to

Step 3

Step 3

If the protocol mode is MGCP, run the

display mgcp attribute

command on the IAD or

choose

MGCP Service Configuration

to check whether the MG domain name

configuration is the same as that on the softswitch.



If no, run the

mgcp mg-domain-name

command on the IAD or choose

MGCP Service

Configuration

to change the domain name.



If yes, go to

Step 4

Step 4

Check whether the softswitch configuration is correct. For details, see the related softswitch
document.



If yes, go to

Step 5



If no, modify the softswitch configuration.

Step 5

Ver ify that the phone number is not used by another phone.

Step 6

Run the

trace

command to trace signaling and locate the cause.

Step 7

Check whether the fault is rectified.



If yes, the procedure ends.



If no, go to

Step 5

Step 8

Contact Huawei technical support.

----End

2.3.20 Port on the IAD208E(M) Is Locked

Symptom

A port on the IAD is locked.

Cause

The possible causes are as follows:



The power supply is incorrect.



The phone connected to the port is not hung up after a conversation ends for a long
period of time.



The splitter is not running properly.



Short-circuit occurs on the user line.

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды