Huawei eSpace IAD Скачать руководство пользователя страница 26

Страница: 26 / 109

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

2.1.15 What should I do if the indicator of a phone is off when the
phone is picked up?

Symptom

The IAD registration status is normal but the indicator of a connected phone is off when the
user picks up the phone.

Possible Cause

The possible causes are as follows:



The phone is faulty.



The device is faulty.



The subscriber line is unavailable.



The power supply is abnormal.

Solution

Step 1

Replace the phone with another one.



If the problem does not occur, the origina l phone is faulty. Replace the original phone.



If the problem persists, go to

Step 2

Step 2

Connect the phone to the telephone line of the IAD and check whether there is feed.



If yes, ensure that the cables in the cable distribution frame (CDF) are correctly
connected.



If no, go to

Step 3

Step 3

Use a telephone line delivered with the device to replace the existing one.



If the problem is resolved, the procedure ends.



If the problem persists, go to

Step 4

Step 4

Replace the board.



If the problem is resolved, the procedure ends.



If the problem persists, go to

Step 5

Step 5

Check the power supply, especial at small ports.



IAD1224: 110/220 V AC or 48 V DC.



IAD132E(T): 100-240 V AC



IAD208E(M ) and IAD104H: 12 V DC (using the power adapter to convert 100-240 V AC to 12 V
DC)



IAD101/102H: 5V DC (using the power adapter to convert 100-240 V AC to 5 V DC)



If yes, go to

Step 6



If no, select the correct power supply.

Step 6

Contact Huawei technical support engineers.

----End

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды