Huawei eSpace IAD Скачать руководство пользователя страница 15

Страница: 15 / 109

eSpace IAD
Troubleshooting

2 Analy zing and Rectify ing Faults

Issue 02 (2012-02-29)

Huawei Proprietary and Confidential

2.1.3 Busy Tone When Picking Up or Dialing a Number

Symptom



Beeps occur on phones connected to the IAD. Users cannot dial numbers.



A user always hears the busy tone when dialing a number.

Cause



The user is not registered with the softswitch.



The called number does not exist.



The short-circuit occurs.



The IAD is faulty.



The mapping between the cable sequence and ports is incorrect.

Solution

Step 1

Ping the softswitch IP address on the IAD.



If the softswitch can be pinged, go to

Step 2



If it cannot be ping through, check whether the network cable is well plugged (ensure
that the uplink cable is plugged in the WAN port of the IAD).

Step 2

Run the

display protocol-mode

command to view the protocol used by the IAD.

Step 3

For SIP services, run the

display sip digitmap

command to query the digitmap configuration.

TERMINAL(config)#

display sip digitmap

If the default digitmap

[XABCD*#].T

is deleted and other digitmaps are not configured, you

cannot initiate any calls. For details about how to configure digitmaps, see the product
document.

Step 4

View the user registration status.



For MGCP services, run the

display mgcp attribute

command to view the user

registration status.



For SIP services, run the

display sip attribute all

command to view the user registration

status.

Step 5

If the user is not registered with the softswitch, verify that the account of the user is enabled
on the softswitch and is configured correctly on the IAD.



For SIP services, you can query the attribute configuration of the SIP services as follows:

−

If the registration fails, check whether the data of the user is configured on the
softswitch.

−

If the user ID or password is inconsistent with that on the softswitch, run the

sip user

command to configure the information.

−

If the IP address of the SIP server configured on the IAD is incorrect, run the

sip

server

index

address

ipaddress

command to configure the information.



For MGCP services, you can query the attribute configuration of the MGCP services as
follows:

−

If the IP address or domain name of the MGC (registration server) is not configured,
run the

mgcp mgc

index

address

ipaddress

command to configure the information. For

Содержание eSpace IAD














































































































Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды

Huawei eSpace IAD, Руководство по устранению неисправностей

Результаты поиска

Содержание eSpace IAD

Отзывы:

Похожие инструкции для eSpace IAD

Бренды по названию

Популярные бренды