Huawei ECC800-Pro Скачать руководство пользователя страница 321

Страница: 321 / 368

Figure 8-22 Device connection

Step 3 Check the monitoring functions of the temperature sensor.

Table 8-37 Function commissioning

Check Method

Normal Connection Status

Path: Monitoring >

Cabinet> IT Cabinet n > T/H

sensor n

You can view the current cabinet temperature.

----End

8.1.7.39 How Can I Set and Add a T/H Sensor (BOM Number: 33010516)?

If a T/H sensor is installed, perform the following steps to configure it.

Prerequisites

One end of the straight-through cable has been connected to the RS485_IN port

on the T/H sensor, and the other end has been connected to the COM port on the

ECC800-Pro or the UIM20A expansion module.

Context

This section describes how to set and add a T/H sensor by using the COM port on

the ECC800-Pro as an example.

Procedure

Step 1 Set the T/H sensor device address.

Set the T/H sensor device address through the DIP switch on the T/H sensor.

Toggle switches 1 to 6 of the DIP switch specify the device address in binary mode.

ON indicates 1, and OFF indicates 0.

Table 8-38 Setting a device address

Address

Toggle

Switch 1

Toggle

Switch 2

Toggle

Switch 3

Toggle

Switch 4

Toggle

Switch 5

Toggle

Switch 6

OFF

ECC800 Data Center Controller

User Manual (for ECC800-Pro)

8 FAQ

Issue 02 (2020-09-07)

310

Содержание ECC800-Pro

















































































































































































































































































































































































Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды

Huawei ECC800-Pro, Руководство пользователя

Результаты поиска

Содержание ECC800-Pro

Отзывы:

Похожие инструкции для ECC800-Pro

Бренды по названию

Популярные бренды