Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 204

Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 88

l

The maximum number of sites supported by the ViewPoint 9039 is 9V + 3A, the maximum
number of sites supported by the ViewPoint 9036 is 6V + 3A, the maximum number of
sites supported by the HUAWEI VP9039A and the ViewPoint 9039S are 6V + 3A, and the
maximum number of sites supported by the HUAWEI VP9036S, ViewPoint 9030 and
HUAWEI VP9035A are 4V + 3A.V stands for video sites and A stands for audio-only sites.
For details, see "

Built-in MCU Capabilities

."

l

HD and dual-stream conferences are supported. For details, see sections

5.4 Experiencing

an HD Conference

5.5 Experiencing an H.239 Dual-Stream Conference

l

Conferences can be locked from the built-in MCU. After a conference is locked, calls from
new sites are restricted.

l

Conferences can be attended by both H.323 and SIP sites and support SIP site control. A
SIP site supports only single-stream transmission. An H.323 site, however, supports dual-
stream transmission.

l

If a conference is held with a built-in MCU, only

Presentation

is available.

Built-in MCU Capabilities

Knowledge of the built-in MCU capability parameters can assist taking advantage of the built-
in MCU function for holding a successful conference.

The capabilities of a built-in MCU vary according to terminal models and the number of licenses.
The following sections take the maximum number of licenses as an example to describe the
capabilities of the built-in MCU.

Number of Video Sites

The maximum number of sites supported by the built-in MCU of the ViewPoint 9039 is 9V +
3A, the maximum number of sites supported by the built-in MCU of HUAWEI VP9039A, the
maximum number of sites supported by the built-in MCU of the ViewPoint 9036, the maximum
number of sites supported by the built-in MCU of the ViewPoint 9039S is 6V + 3A, and the
maximum number of sites supported by the built-in MCU of the HUAWEI VP9036S, ViewPoint
9030 and the HUAWEI VP9035A are 4V + 3A in which V stands for video sites and A stands
for audio-only sites.

Maximum Number of Sites Supported by the Built-In MCU of the ViewPoint 9039:

l

9 SD video sites + 3 audio sites

l

6 HD video sites + 3 audio sites

Maximum Number of Sites Supported by the Built-In MCU of the ViewPoint 9036:

l

6 SD video sites + 3 audio sites

l

4 HD video sites + 3 audio sites

Maximum Number of Sites Supported by the Built-In MCU of the HUAWEI VP9039A and the
ViewPoint 9039S:

l

6 SD video sites + 3 audio sites

l

6 HD video sites + 3 audio sites

Maximum Number of Sites Supported by the Built-In MCU of the HUAWEI VP9036S,
ViewPoint 9030 and the HUAWEI VP9035A:

l

4SD video sites + 3 audio sites

HUAWEI 9000 HD Video Terminal
Administrator Guide

5 Initiating a Conference

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

76

«
...
86
87
88
89
90
...
»

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов