Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 204

Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 62

TIP

The text on the upper left corner indicates the camera that is currently being controlled (local or remote).

----End

3.3.3 Controlling a Camera

You can exercise PTZ control over a local or remote camera.

Prerequisites

Before you use PTZ functions, ensure that the VISCA control cable is connected to the COM
interface of the terminal properly and that the relevant configuration is correct.

Procedure

Step 1

Press

, and then follow the displayed instructions to access the camera control screen.

Step 2

From the camera control screen, you can:

l

Press

to switch between local and remote cameras. The text on the upper left corner

indicates the camera that is currently being controlled (local or remote).

l

Press arrow keys to turn the camera lens.

l

Press

to zoom in or

to zoom out.

----End

Follow-up Procedure

Press the

key on the remote control, and then select

Reset

. You can then follow the

instructions to restore the local camera to its default settings.

3.4 Saving and Using Camera Presets

A camera preset is a set of camera settings that have been saved in advance. You can set these
presets in advance.

If a camera supports pan, tilt, and zoom (PTZ) functions, a maximum of 30 camera presets can
be created and saved. Each camera preset saves the camera number, zooming level, and camera
direction. A camera preset remains valid until it is deleted or changed.

describes the features of camera presets.

Table 3-7

Features of camera presets

Terminal

Number of Preset
Positions

Is the Data Lost After Restart?

Local terminal

30

NOTE

Local camera

set to

SD-CVBS

IN 1

, nine local preset positions

are available.

No

HUAWEI 9000 HD Video Terminal
Administrator Guide

3 Camera and Display

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

50

«
...
60
61
62
63
64
...
»

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов