Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 204

Huawei 9000 VCT V100R011 Скачать руководство пользователя страница 24

The cable connection methods for different models are similar. Therefore, the following section
takes the ViewPoint 9039 and the HUAWEI VP9039A as examples.

Figure 1-15

shows the cable connection of the ViewPoint 9039 and the HUAWEI VP9039A in

the simplest configuration. With the following cable connection, the terminal outputs HD video
and uses the local area network (LAN) for communications. An HD camera is used for HD video
input and a microphone array is used for audio input.

Figure 1-15

Cable connection for the terminal in the simplest configuration

BNC

SMB

RJ45

VISCA

HDMI

DVI

RCA

RCA

SXGA

SXGA

RJ45

RJ45

DVI

DVI

RJ45

RJ45

mini HDMI mini HDMI

I

I

PUSH

1

2

3

PUSH

1

2

3

DVI

SXGA

DVI

SXGA

SMB

BNC

RJ45

VISCA

RJ45

RJ45

mini HDMI mini HDMI

HDMI

DVI

RJ45

RJ45

RCA

RCA

The configuration details are as follows:

l

Video input: Use the BNC-SMB cable provided, connect the HD SDI video output interface
of a camera to the HD IN 1 interface of the terminal. Then connect the COM 1 interface of
the terminal to the camera control interface using the camera control cable.

l

Computer desktop input: Connect the HD IN 3 interface of the terminal to the VGA output
interface of the computer using the DVI-SXGA cable provided.

l

Audio input: Connect the MIC LAN-POE interface of the terminal to the microphone array
using the POE cable (both provided).

l

Video output: Connect the HD OUT 1 interface of the terminal to the HDMI input interface
of an HD TV using the DVI-HDMI cable provided.

l

Video output: To independently output presentation contents, connect the HD OUT 2
interface of the terminal to the VGA input interface of a projector using the DVI-SXGA
cable provided.

HUAWEI 9000 HD Video Terminal
Administrator Guide

1 Installation and Preparation

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

12

«
...
22
23
24
25
26
...
»

Содержание 9000 VCT V100R011













































































































































































































Отзывы:

Нет отзывов