Huawei 3900 Series Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 196

background image

7

Commissioning the MBTS by Using Local

Maintenance Terminal and M2000

About This Chapter

This chapter describes how to use local maintenance terminal at the MBTS to upgrade MBTS
software and configure MBTS data, check MBTS hardware status, rectify MBTS hardware faults
(if any) to facilitate the establishment of MBTS OM channels. This chapter also describes how
to check the operating status of the MBTS on the M2000.

NOTE

The GBTS local maintenance terminal is named SMT, the NodeB local maintenance terminal is named
NodeB LMT, and the eNodeB local maintenance terminal is named eNodeB LMT. Select a local
maintenance terminal according to the mode of the base station to be commissioned.

7.1 Procedure for Commissioning the MBTS Using Local Maintenance Terminal and M2000

At the local end of the MBTS, you can use local maintenance terminal to upgrade MBTS software
and configure MBTS data and to facilitate the establishment of MBTS OM at the MBTS. You
can also check whether the MBTS hardware status is normal according to the board status and
LED status, to locate and rectify faults (if any) in time. At the M2000, you can check the MBTS
operating status.

7.2 Running the GBTS SMT

To run the GBTS site maintenance terminal (SMT), you need to first set the IP address of the
SMT client, connect the base station and the SMT, and then log in to the SMT.

7.3 Configuring the Basic Data of the GBTS

This section describes how to configure the basic data of the GBTS such as the GBTS boards
and logical objects. You must configure the basic data of the GBTS before performing the local
commissioning on the GBTS side.

7.4 Checking the Transmission Between the BBU and the BSC on the BTS Side

This section describes how to check the status of the LEDs on the panels of the GTMU and
UTRP (if the UTRP is installed) and how to check the connections of the E1 cable and E1 surge
protection transfer cable to ensure that the BBU properly communicates with the BSC.

7.5 Running the NodeB LMT

To run the NodeB LMT, you need to first set the IP address of the LMT client, connect the base
station and the LMT, and then log in to the LMT.

3900 Series Multi-Mode Base Station
Commissioning Guide

7 Commissioning the MBTS by Using Local Maintenance

Terminal and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

7-1

«
...
143
144
145
146
147
...
»

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

Бренд: Veris Industries Страницы: 2

Бренд: Keating Of Chicago Страницы: 2

Бренд: LaserTrack Страницы: 12

Бренд: paramondo Страницы: 44

Бренд: IHP Страницы: 2

ipRocketLink 3086FR

Бренд: Patton electronics Страницы: 6

Бренд: Q-See Страницы: 28

Бренд: quadient Страницы: 2

AcousticDesign AD-S52

Бренд: QSC Страницы: 4

Бренд: QC Conveyors Страницы: 32

Бренд: Defy Страницы: 48

Бренд: Anslut Страницы: 6

Бренд: Uebler Страницы: 56

Бренд: topmark Страницы: 32

Бренд: Leuze electronic Страницы: 10

Бренд: Sachtler Страницы: 26

Бренд: Quadratec Страницы: 12

Бренд: ABC Design Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды