Huawei 3900 Series Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 196

background image

ALL=GTMU|DRFU|GRFU

Where,

ALL=XXXX

is set by the user manually and it specifies the type of the board onto

which the software is to be loaded. In the preceding example, the software is to be loaded
onto the GTMU, DRFU, and GRFU.

CAUTION

l

All letters are in capitals, and different board names are separated by "|". Do not add
any comment or press the space or TAB key before or after "=" or the name of each
board.

l

The base stations using different configurations cannot use the same configuration file.
New configuration files should be created for the base stations of different
configurations.

2.

Save the configuration script in ANSI characters.

Step 5

The data configuration file is made and exported through the CME. This is usually performed
by configuration engineers.

Step 6

Store the files according to the following path, as shown in

.

Table 6-1

Saving path of the file

File

Specified Path of the USB Storage
Device

Upgrade software package

\\BTS3900 GSM

Configuration script

\\BTS3900 GSM\Precfg.ini

Data configuration file

\\BTS3900 GSM\SiteName\TranCfg.ini

----End

6.2.2 Arranging the USB Disk for Local NodeB Commissioning

The USB disk should be ready before it is used for local NodeB commissioning.

Procedure

Step 1

Prepare the USB disk with a LED. The requirements are as follows: when there is no read or
write operation on the USB disk, the LED on the USB disk is ON; when there is any read or
write operation on the USB disk, the LED on the USB disk is blinking.

Step 2

Check the compatibility of the USB disk with the NodeB. Do as follows to test the USB disk:
Insert the USB disk into the USB port on the WMPT of a NodeB that runs normally, and wait
for 3 seconds. If the LED on the USB disk blinked once, it indicates that the USB disk is
functional. If the USB disk fails the preceding test, change the USB disk.

Step 3

Save the related files in the USB disk according to the specified path.
1.

Prepare the NodeB software package, data configuration file, and VSWR check script file.

3900 Series Multi-Mode Base Station
Commissioning Guide

6 Commissioning the MBTS by Using USB and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

6-7

«
...
123
124
125
126
127
...
»

Содержание 3900 Series





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3900 Series

Super G3 FAX Board-T1

Бренд: Canon Страницы: 16

iP4000 - PIXMA Photo Printer

Бренд: Canon Страницы: 3

Бренд: Canon Страницы: 21

Бренд: Canon Страницы: 6

7215 - LV XGA LCD Projector

Бренд: Canon Страницы: 8

Бренд: Barco Страницы: 2

Бренд: Barco Страницы: 22

Бренд: Camtree Страницы: 2

Бренд: Camtree Страницы: 11

Бренд: Camtree Страницы: 4

Бренд: Eclipse Страницы: 6

AdvancedPunch Pro

Бренд: GBC Страницы: 92

Бренд: ibis Страницы: 12

Бренд: IAME Страницы: 17

Бренд: M7 SPEED Страницы: 11

Бренд: X4-Life Страницы: 2

Бренд: Xblitz Страницы: 16

Бренд: Axxess Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды