manualshive.com logo in svg

HTP Mod Con 300 VWH, Инструкция по установке и обслуживанию

"HTP Mod Con 300 VWH" - это высокоэффективный котел с максимальной производительностью. Для правильной установки и обслуживания следуйте инструкциям в руководстве по установке и обслуживанию. Скачать это руководство бесплатно можно на manualshive.com. Позаботьтесь о своем оборудовании, загрузив руководство прямо сейчас.

Поделиться
Скачать
background image

4 

 

 

                                                                                       LP- 276 REV. 9.4.14 

The latest version of the National Electrical Code, NFPA No. 70. 
 

NOTE:

 The gas manifold and controls met safe lighting and other performance criteria when the boiler underwent tests specified in 

ANSI Z21.13 – latest edition. 
 

 

The hydronic supply and return connections of these products are for installation in closed loop systems ONLY!

 Use of this 

product in any manner other than described in this manual may result in premature product failure, substantial property damage, severe 
personal injury, or death. Damage or failure of this product (or the system in which it is installed) due to unauthorized use 

IS NOT 

COVERED BY WARRANTY

.   

 

NOTICE

 

The CSD-1 ASME Code, Section CW-400 requires that hot water heating and supply boilers have a) a UL 353 temperature control 
device, b) at least one (1) temperature-actuated control to shut off the fuel supply when system water reaches a preset operating 
temperature, c) a high temperature limit control that prevents the water temperature from exceeding the maximum allowable 
temperature by causing a safety shutdown and lockout, and d) its own sensing element and operating switch. 
 
The temperature control system integrated into the 926 control provided with this heating appliance complies with the requirements of 
CSD-1 Section CW-400 as a temperature operation control. The control monitors the temperature difference between the inlet and the 
outlet sensor, which is affected by boiler water flow. If this temperature difference exceeds 55°F (typically because of low water flow or 
very low heat load), the control will reduce the maximum fan speed. If the temperature difference exceeds 60°F, the control will 
effectively sense there is little or no water flow or heat load and shut the boiler down. The controller will restart automatically once the 
temperature difference has dropped below 55°F and the minimum off time (anti-cycle time) has expired. In addition, if the control 
senses that the outlet water temperature has reached 210°F, the boiler is put into a hard lockout and requires manual reset to restart. 

TABLE OF CONTENTS 

PART 1 – GENERAL SAFETY INFORMATION .......................................................................................................................... 6

 

A. PRECAUTIONS .......................................................................................................................................................................... 6

 

B. IMPROPER COMBUSTION ........................................................................................................................................................ 7

 

C. GAS ............................................................................................................................................................................................ 7

 

D. WHEN SERVICING THE BOILER .............................................................................................................................................. 7

 

E. BOILER WATER ......................................................................................................................................................................... 7

 

PART 2 – BEFORE YOU START ................................................................................................................................................ 7

 

A. WHAT’S IN THE BOX ................................................................................................................................................................. 9

 

B. HOW BOILER OPERATES ......................................................................................................................................................... 9

 

C. OPTIONAL EQUIPMENT ......................................................................................................................................................... 10

 

PART 3 – PREPARE BOILER LOCATION ............................................................................................................................... 10

 

A. BEFORE LOCATING THE BOILER .......................................................................................................................................... 10

 

B. LEVELING AND DIMENSIONS ................................................................................................................................................ 11

 

C. CLEARANCES FOR SERVICE ACCESS ................................................................................................................................. 13

 

D. RESIDENTIAL GARAGE INSTALLATION ................................................................................................................................ 13

 

E. EXHAUST VENT AND INTAKE AIR VENT ............................................................................................................................... 13

 

F. PREVENT COMBUSTION AIR CONTAMINATION .................................................................................................................. 13

 

G. REMOVING A BOILER FROM A COMMON VENT SYSTEM .................................................................................................. 14

 

H. UNCRATING AND MOVING BOILER ...................................................................................................................................... 15

 

PART 4 – BOILER PIPING ........................................................................................................................................................ 15

 

A. GENERAL PIPING INFORMATION .......................................................................................................................................... 15

 

B. RELIEF VALVE ......................................................................................................................................................................... 16

 

Содержание Mod Con 300 VWH










































































Отзывы:

Нет отзывов

Похожие инструкции для Mod Con 300 VWH

Vaillant aquaPLUS VUI 362-7 Instructions For Installation And Servicing preview
aquaPLUS VUI 362-7
Бренд: Vaillant Страницы: 60
Dettson HYDRAI016-208-3 Installation Instructions And Owner'S Manual preview
HYDRAI016-208-3
Бренд: Dettson Страницы: 20
Nieco FH94 Electric Owner'S Manual preview
FH94 Electric
Бренд: Nieco Страницы: 40
D'Alessandro Termomeccanica CSL25 Use And Maintenance Manual preview
CSL25
Бренд: D'Alessandro Termomeccanica Страницы: 14
A.O. Smith 100 Series Instruction Manual preview
100 Series
Бренд: A.O. Smith Страницы: 52
RedOne RO-WB10L Instruction Manual preview
RO-WB10L
Бренд: RedOne Страницы: 3
Immergas Nike Star 24 4 ErP Instruction And Warning Book preview
Nike Star 24 4 ErP
Бренд: Immergas Страницы: 28
Immergas NIKE MYTHOS 24 4 ERP Instruction And Warning Book preview
NIKE MYTHOS 24 4 ERP
Бренд: Immergas Страницы: 28
Immergas HERCULES SOLAR 26 2 ErP Instruction And Recommendation Booklet preview
HERCULES SOLAR 26 2 ErP
Бренд: Immergas Страницы: 52
Ideal Boilers Mexico Super CF 3/40 Installation & Servicing Manual preview
Mexico Super CF 3/40
Бренд: Ideal Boilers Страницы: 36
Ideal Boilers Classic RS 245 P Installation And Servicing preview
Classic RS 245 P
Бренд: Ideal Boilers Страницы: 28
Potterton PROFILE LPG 100e Installation And Servicing Instructions preview
PROFILE LPG 100e
Бренд: Potterton Страницы: 30
Rinnai Q Premier QP130N Installation & Servicing Instructions Manual preview
Q Premier QP130N
Бренд: Rinnai Страницы: 94
Wolf RB36 Owner'S Manual preview
RB36
Бренд: Wolf Страницы: 8
Wolf FHBO Installation & Operation Owner'S Manual preview
FHBO
Бренд: Wolf Страницы: 8
Ferroli DOMIcompact F 24 B Instructions For Installation, Use And Maintenance Manual preview
DOMIcompact F 24 B
Бренд: Ferroli Страницы: 44
IDEAL Concord Super Series 4 100 V Installation And Servicing preview
Concord Super Series 4 100 V
Бренд: IDEAL Страницы: 40
UTICA BOILERS MGB Series Installation, Operation & Maintenance Manual preview
MGB Series
Бренд: UTICA BOILERS Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды