HTP Hydra Smart RT-199 Скачать руководство пользователя страница 14

Страница: 14 / 48

LP-532 REV. 8.13.2014

Description/Part #

Inlet Water Filter / 7850P-017

Check Point

(Main PCB)

N/A

Function

This component consists of durable STS, PPS material for filtering out debris and heavy

metals.

Failure Event

Input capacity of cold water is not constant and thermal efficiency is poor.

Effects

Noise at the heat exchanger is generated and pipes are blocked by the debris.

Error Code

N/A

Diagonostic

Clean the Cold water inlet filter.

Color / Wire Number

N/A

Description/Part #

Flow Control Valve / 7850P-053

Check Point

(Main PCB)

CN 14, CN 3

Function

The component detects water flow and regulates water flow rate in order to supply

stable hot water (More than 0.5 GPM).

Failure Event

Water flow rate is not detected and water leakage occurs around the flow control valve.

Effects

① Ignition sequence does not start.

② Operation of product is stopped once water leakage is detected.

Error Code

Er 65

Diagonostic

① Restart the unit

② Check the connection around the flow control valve.

Color / Wire Number

[IWM (Inlet Water Modulation)]

GND (yellow) : connector ①

IWM Stepper motor position (green) : connector②

VDD (white) : connector ③

IWM Stepper motor coil X phase (red) : connector ④

IWM Stepper motor coil Y phase (black) : connector ⑤

VDD (blue) : connector ⑥

IWM Stepper motor coil /X phase (orange) : connector ⑦

IWM Stepper motor coil /Y phase (brown) : connector ⑧

1. PPS material Body

2. Hall sensor rated voltage

DC5~24V 10mA. Max

3. Operating Fluid :

0℃~80℃ (32 ~ 176℉)

4. Operating range :

1.2 ~ 30ℓ (0.32 ~ 8 gpm)

VCC (red) : connector

④

Water flow sensor (white) : connector

⑤

GND (blue) : connector

⑥

Inlet water filter

① ② ③ ④ ⑤ ⑥

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨

① ② ③ ④ ⑤ ⑥ ⑦ ⑧

Chapter 2 Components description

Содержание Hydra Smart RT-199

















































Результаты поиска

Содержание Hydra Smart RT-199

Отзывы:

Похожие инструкции для Hydra Smart RT-199

Бренды по названию

Популярные бренды

HTP Hydra Smart RT-199, Руководство по обслуживанию

Результаты поиска

Содержание Hydra Smart RT-199

Отзывы:

Похожие инструкции для Hydra Smart RT-199

Бренды по названию

Популярные бренды