HTP EnduroTI ETI-1000 Скачать руководство пользователя страница 55

Страница: 55 / 67

LP-517 Rev. 000 Rel. 019 Date 7.21.20

LINE VOLTAGE E19

PUMP OFF

E19 indicates the line voltage frequency

is out of range. This could happen if the

boiler is being powered from a small

gasoline powered generator that is

overloaded or not functioning correctly.

Inspect power wiring to the boiler and repair as necessary. If

connected to line voltage, notify the power company. If connected

to an alternate power source such as a generator or inverter, make

sure the line voltage frequency supplied by the device is 47 - 62.5 Hz.

BURNERTEMPBLOCK E28

PUMP ON TIME

This error indicates the burner sensor

has exceeded 199

F. The burner will re-

fire once the burner temperature drops

below 181

F. If this occurs more than

five times in ten minutes during a single

heat demand, an F28 lockout code is

generated.

1. Check sensor by turning off the gas and allowing the unit to go

through pre-purge and post purge cycles. While air is flowing through

the burner check the burner sensor value on the display. This value

should similar to the current intake air temperature. If this value is

much different than the current intake air, check sensor resistance

and wiring. If resistance values are out of range replace sensor.

2. If sensor is ok, check combustion, often a rich combustion setting

elevates burner temperatures. Ensure there are no blockages on

either the intake or the exhaust. Confirm the combustion is set

to proper CO2 numbers, especially on low fire. After adjusting

combustion, re-start the boiler and observe the burner temperature

on the display. This should be done both on high and low fire.

Table 27 - Boiler Error and Fault Codes

Outdoor Sensor

(7250P-319)

Supply Temperature

Sensor

(7250P-324)

Indirect Sensor

(7350P-325)

Boiler

Sensor

(7700P-

073)

Flue

Temperature

Sensor

(6300P-023)

Burner

Temperature

Sensor

(6300P-036)

Temperature (

Resistance

(ohms)

Temperature (

Resistance (ohms)

-22

171800

32624

-13

129800

25381

-4

98930

19897

76020

15711

58880

12493

45950

10000

36130

8056

28600

6530

22800

104

5324

18300

113

4365

14770

122

3599

12000

131

2982

9804

140

2483

8054

149

2079

104

6652

158

1748

113

5522

167

1476

176

1252

185

1066

194

912

203

782

212

674

Table 28 - Sensor Temperature Resistance

Содержание EnduroTI ETI-1000




































































Результаты поиска

Содержание EnduroTI ETI-1000

Отзывы:

HTP EnduroTI ETI-1000, Установка, Запуск, Обслуживание, Запчасти, Гарантия, Страница: 55 / 67

Результаты поиска

Содержание EnduroTI ETI-1000

Отзывы: