manualshive.com logo in svg

HTC 1500 IXT, Руководство пользователя

Поделиться
Скачать
HTC 1500 IXT Скачать руководство пользователя страница 17

HTC 1500 ixT

Safety

3.0

7

Warning!

Disconnect the electrical supply and raise the grinding head when

changing tools or repairing the machine.

Warning!

The machine must only be used and moved on level surfaces.

There is a risk of crushing if the machine starts to roll.

Warning!

Inspect the floor carefully and remove any objects sticking up and

any loose rubbish that may otherwise get stuck in the machine and

cause personal injury or damage to the machine. 

Warning!

Do not clean the machine using a high-pressure washer, otherwise

moisture may penetrate electrical elements and damage the

machine’s drive system.

Warning!

There is a risk of crushing when locking the bar. Ensure that you

do not place your fingers between the bar and the foot pedal.

Warning!

During charging, oxyhydrogen gas always forms in the battery. An

open flame or spark in the vicinity of the batteries could cause an

explosion.

2.3. Observations

Note!

The machine may only be used to grind and polish natural stone,

terrazzo, concrete, or other materials stated in this manual or that

are approved by HTC.

Содержание 1500 IXT





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды