HT HT4013 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 21

background image

HT4013

EN – 14

4.3.7. Temperature measurement with type K probe

CAUTION

Do not put the temperature probe into contact with live surfaces. Voltages
higher than 30Vrms or 60VDC imply electrical shock hazard.

Fig. 8: Use of the clamp for temperature measurement

1. Select the Temp°C°F position. The instrument is set to °C measurement
2. Press the MODE key until the symbol “°F“ is displayed to activate °F measurement
3. Insert the K wire probe provided into input terminal V



CAPHz%Temp and COM

by means of the relevant adapter, respecting the polarity indicated in Fig. 8. The
display shows the value of temperature.

4. To use the HOLD function, please refer to § 4.2.

«
...
13
14
15
16
17
...
»

Содержание HT4013






















Отзывы:

Нет отзывов

Похожие инструкции для HT4013

Бренд: ParTech Страницы: 14

Бренд: Valeport Страницы: 27

SXNP10 - DIGITAL PIANO

Бренд: Panasonic Страницы: 63

Бренд: Labom Страницы: 5

POCKET COLORIMETER II

Бренд: Hach Страницы: 188

CP-4900 Micro-GC

Бренд: Varian Страницы: 13

Бренд: Cal Test Electronics Страницы: 12

Бренд: LEGRAND Страницы: 5

Digital Piano CA750

Бренд: Kawai Страницы: 76

Бренд: PCE Health and Fitness Страницы: 11

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

DigiFlow 6710M-22

Бренд: Savant Страницы: 3

Бренд: Agilent Technologies Страницы: 198

Бренд: Hanna Instruments Страницы: 28

Бренд: b&o Страницы: 32

Бренд: Orange Research Страницы: 2

Бренд: Sub Aqua Страницы: 4

Бренд: Fluke Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды