manualshive.com logo in svg

HT GroundTest M71, Руководство пользователя, Страница: 16 / 26

Поделиться
Скачать
HT GroundTest M71 Скачать руководство пользователя страница 16

  

GroundTest 

M71 

 

 

EN – 15 

 

4.5.2.  EARTH 3W- Measurement procedure 

 

 

CAUTION 

 

 

The instrument can be used for voltage and  current measurements on 
installations with overvoltage category  equal to CAT III 240V to earth and 
maximum voltage of  415V between inputs. Do not connect the instrument to 
installations whose voltages exceed the limits indicated in this manual. 
Exceeding such limits may cause electric shock to the user and damage the 
instrument.  

 

 

Fig. 6: Instrument's wiring for three-wire earth measurement 

 

  For small sized installations, place the ampere metric probe (terminal H, blue wire) at a 

distance equal to five times the diagonal of the earth installation and the volt metric 
probe (terminal S, red wire) at a distance equal to about 2.5 times the diagonal of the 
earth installation 

 

  For large sized installations, place the ampere metric probe (terminal H, blue wire) at a 

distance equal to the diagonal of the earth installation and the volt metric probe 
(terminal S, red wire) at a distance equal to about 0.5 times the diagonal of the earth 
installation 
 

  In the latter case several measurements shall be carried out moving the volt metric 

probe back and forth (along the measurement direction) with respect to the middle 
point and checking that the result is nearly constant. 

 
 

Содержание GroundTest M71



























Отзывы:

Нет отзывов