HSM HSM1822, Инструкция по эксплуатации

Страница: 18 / 93

06/2013
SECURIO B 32
17
english
9 Technical data
Cutting type Strip cut Cross cut
Cut size (mm) 5.8 3.9 4.5 x 30 1.9 x 15 0.78 x 11 1 x 5
Security level DIN 66399 P-2 / O-2
T-2 / E-2
P-2 / O-2
T-2 / E-2
P-4 / O-3
T-4 / E-3
F-1
P-5 / T-5
E-4 / F-2
P-6 / F-3 P-7 / F-3
Cutting capacity* (sheets), A4 70 g/m 2
80 g/m
2
28 - 30
25 - 27 22 - 24
19 - 21 17 - 19
14 - 16 11 - 13
9 - 11
7
6 5
4
Weight 25.5 kg 27 kg
Cutting speed 65 mm/s
Intake width 310 mm
Power supply 230 V, 50 Hz 110 V - 120 V, 60 Hz 220 V, 60 Hz
Power consumption
with max. number of sheets
500 W
Operating mode
Continuous operation
Ambient conditions in operation:
Temperature
Relative humidity
Height above sea-level (MSL)
-10 °C to +25 °C
max. 90 %, without condensation
max. 2,000 m
Size W x D x H (mm) 497 x 398 x 793
Shredded material container volume 82 litres
Sound pressure level emissions
(Idle running/ load)
56 dB (A) / 59 - 63 dB (A)
* The maximum number of sheets (DIN A4, 70 g/m² or 80 g/m²), fed lengthways, which can be cut in one cycle. The
performance data is determined when the motor is cold and the cutting device is freshly oiled. A weaker mains voltage
or a different mains frequency to the one speci
fi ed could result in less sheet capacity and increased noise during op-
eration. The sheet capacity can vary depending on the structure and properties of the paper and on the way it enters.
The performance data in 80 g/m² is calculated.
EC Declaration of Conformity
The manufacturer HSM GmbH + Co. KG , Austraße 1 - 9, 88699 Frickingen / Germany hereby declares that the ma-
chine, referred to here as
document shredder
Securio B32
corresponds to the health and safety requirements of the following EC directives listed below due to its conception and
design of the version in which it was put into circulation by us:
Low voltage directive 2006 / 95 / EEC
EMC directive 2004 / 108 / EC
Applied standards and technical speci fi cations:
• EN 55014-1:2006 + A1:2009 • EN 61000-4-2:1995 + A1:1998 + A2:2001
• EN 55014-2:1997 + A1:2001 + A2:2008 • EN 61000-4-4:2004
• EN 61000-3-2:2006 + A1:2009 + A2:2009 • EN 61000-4-5:2006
• EN 61000-3-3:2008 • EN 61000-4-6:2007 + Corr. August 2007
• EN 62233:2008 • EN 61000-4-11:2004
• EN 60950-1:2006 + A11:2009 + A1:2010
Frickingen, 27.5.2013
ppa. Hubert Kötzinger - Head of Environmental Engineering Product Development