background image

 

 

Problem

 

Solution

 

Wireless remote (thermo-
hygrometer) not reporting in to 
console. 

If any of the sensor communication is lost,  
The maximum line of sight communication range 
is 100 meters and 30 meters under most 
conditions. Move the sensor assembly closer to 
the display console. 
 
If the sensor assembly is too close (less than 

5’), 

move the sensor assembly away from the display 
console. 
 
Make sure the remote sensor LCD display is 
working and the transmitter light is flashing once 
per 48 seconds. 
 
Install a fresh set of batteries in the remote 
thermo-hygrometer. For cold weather 
environments, install lithium batteries. 
 
Make sure the remote sensors are not 
transmitting through solid metal (acts as an RF 
shield), or earth barrier (down a hill). 
 
Move the remote sensors around electrical noise 
generating devices, such as computers, TVs and 
other wireless transmitters if used indoor. 
 
Move the remote sensor to a higher location. 
Move the remote sensor to a closer location. 

Temperature sensor reads too high 
in the day time. 

Make sure the thermo-hygrometer is mounted in a 
shaded area on the north facing wall.  

Indoor and Outdoor Temperature do 
not agree 

Allow up to one hour for the sensors to stabilize 
due to signal filtering. The two temperature 
sensors should agree within 2 °C (the sensor 
accuracy is ± 1 °C). 

Indoor and Outdoor Humidity do not 
agree 

Allow up to one hour for the sensors to stabilize 
due to signal filtering. The two humidity sensors 
should agree within 10 % (the sensor accuracy is 
± 5 %). 

Display contrast is weak 

Replace console batteries with a fresh set of 
batteries. 

 
 
 
 

Содержание froggit FT-Comfort












Отзывы: