1. The operation and range of your Long Range Wireless Door Chime depends on location,
temperature and battery condition.
2. Try different locations in your home, ideally 1 metre from floor. Move Door Chime Receiver closer to
Bell Press Transmitter to improve operation.
3. Do not expose either unit to rain or immerse in water.
4. Avoid locations where the Bell Press Transmitter is exposed to direct summer sunlight.
5. Do not leave exhausted batteries in Door Chime Receiver or Bell Press Transmitter.
6. Clean only with a damp cloth and mild detergent. Do not use solvents
8 Important Notes
Up to 70 metres. NOTE: Range depends on location, temperature and battery condition.
Up to 70 metres. NOTE: Range depends on location, temperature and battery condition.
Door Chime Receiver
Step 1:
Depress tab on Door Chime Receiver to remove back cover plate.
Step 2:
Insert 3 x ‘C’ size alkaline batteries ensuring that the coil springs contact the negative (-) end of
each battery.
The Door Chime Receiver is fully portable and free-standing and can be placed anywhere in the house
(e.g., table, bookshelf, cupboard, mantelpiece, window sill, etc). It can also be fixed temporarily or
permanently to a wall as required.
BEFORE PERMANENTLY FIXING BELL PRESS AND DOOR CHIME RECEIVER IN PLACE, TEST LOCATION
OF BOTH UNITS TO ENSURE SATISFACTORY OPERATION.
The Door Chime Receiver has one slotted hang hole on the back. This hole will enable the Door Chime
Receiver to be hooked onto a screw and easily removed or relocated.
Bell Press Unit
Step 1:
Remove front plate cover by lifting bottom edge and sliding out.
Step 2:
Insert 12V battery (included in pack) ensuring the
positive (+) end of the battery is at the (+) in the battery
compartment. (see Fig 1.).
Step 3:
Replace front plate cover.
Step 4:
Press the Push Button to ensure that the red LED indicator
lamp lights, indicating that the battery is correctly installed.
Step 5:
Fix the unit either directly to your front door or a position
close by using the self-adhesive foam mounting pads
supplied. The chosen mounting position should not be
exposed to direct sunlight or rain. The device can also be
used as a remote control and doesn’t require any installation.
IMPORTANT:
Do not mount the Bell Press Transmitter on metal or near a metal door frame, security door,
or in close proximity to any metal outdoor furniture as the range of the unit will be substantially reduced.
The Bell Press Transmitter has one 12 volt battery (type 3LR50) included which should last about 850
days (in excess of 2 years) under normal operating conditions.
The Door Chime Receiver is powered by 3 x ‘C’ size batteries (not included). Alkaline batteries are
recommended for longer operating life, up to 180 days.
IMPORTANT:
Do not use rechargeable batteries, do not mix old and new batteries or different types.
3
6
4
5
Range
Installation
Bell Press Transmitter
Door Chime Receiver
Bell Press
Transmitter
Press the button on the Bell Press Transmitter. The Door Chime will sound. Press Chime Button again
to repeat chime.
7 Door Chime Operation
The tone selector is located in the Bell Press Transmitter. The two last pins (see Fig 2) are the
2 possible chime tones. To change tone simply remove jumper and fit on the last row of pins.
Tone Selection
10
12 Troubleshooting
PROBLEM
POSSIBLE CAUSE
SUGGESTED SOLUTION
The Door Chime is
intermittent when it
is activated or sounds
when not activated.
A similar door chime with the same
frequency is operated nearby.
Change the channel of your Door
Chime and Bell Press (refer to
Changing Operating Channels).
9 Changing Operating Channels
Should your Door
Chime Receiver activate
intermittently for no
reason, it is possible
that the uncontrolled
activation may be
caused by another unit
operating nearby on the
same frequency coding.
The encoded frequency
of the transmitter (Bell
Press Transmitter)
and receiver (Door
Chime Receiver) can be
changed to avoid this
problem.
First, turn the two devices so their backs are facing you. Using long nose pliers, place a jumper (small
black device included in pack with the adhesive ‘ foam pads’ or double-sided tape) on the same row of
pins on both devices. To change the preset channel place the jumpers on same row #. (See Fig 2.)
It is essential that the jumper positions are the same for both units. Test to ensure correct operation.
NB: Use of long nose pliers to install jumper may be required.
BACK OF DOOR CHIME
RECEIVER
Radio
Wave
Sound
Chime
Two last pins
are the sound
chimes.
First 6 pins are
the radio wave
channels.
For example:
Jumper on Row #3 in both units
to be on the same channel.
BACK OF
BELL PRESS
TRANSMITTER
OPE
N
Figure 2.
Figure 1.
