HPE ProLiant e910 Скачать руководство пользователя страница 77

Страница: 77 / 182

You can access the

Update Firmware, Upload to iLO Repository, and Add to Queue controls from all tabs on the Firmware

& OS Software page.

For more information, see the

Firmware Updates video.

Viewing installed firmware information

Procedure

1. Click Firmware & OS Software in the navigation tree.

The

Installed Firmware page displays firmware information for various server components. If the server is powered off, the

information on this page is current as of the last power off. Firmware information is updated only when the server is
powered on and POST is complete.

2. (Optional) To sort by a table column, click the column heading.

To change the sort order to ascending or descending, click the column heading again or click the arrow icon next to the
column heading.

Firmware types

The firmware types listed on the

Installed Firmware page vary based on the server model and configuration.

For most servers, the system ROM and iLO firmware are listed. Other possible firmware options include the following:

• Power Management Controller

• Server Platform Services Firmware

• Smart Array

• Intelligent Platform Abstraction Data

• Smart Storage Energy Pack

• TPM or TM firmware

• SAS Programmable Logic Device

• System Programmable Logic Device

• Intelligent Provisioning

• Networking adapters

• NVMe Backplane firmware

• Innovation Engine (IE) firmware

• Drive firmware

• Power Supply firmware

• Embedded Video Controller

• Language packs

• HPE Persistent Memory

Firmware details

The

Installed Firmware page displays the following information for each listed firmware type:

Using HPE iLO 5

Содержание ProLiant e910























































































































































































Результаты поиска

Содержание ProLiant e910

Отзывы:

Похожие инструкции для ProLiant e910

Бренды по названию

Популярные бренды

HPE ProLiant e910, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание ProLiant e910

Отзывы:

Похожие инструкции для ProLiant e910

Бренды по названию

Популярные бренды