HPE ProLiant DL180 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 172

background image

Software and configuration utilities

Server mode

The software and configuration utilities presented in this section operate in online mode, offline mode, or
in both modes.

Software or configuration utility

Server mode

Active Health System

on page 146

Online and Offline

on page 147

Online and Offline

HPE Smart Storage Administrator

Online and Offline

iLO RESTful API

on page 149

Online and Offline

Intelligent Provisioning

on page 149

Online and Offline

Scripting Toolkit for Windows and Linux

on

page 151

Online

Service Pack for ProLiant

on page 155

Online and Offline

Smart Update Manager

on page 155

Online and Offline

UEFI System Utilities

Offline

Product QuickSpecs

For more information about product features, specifications, options, configurations, and compatibility, see
the product QuickSpecs on the Hewlett Packard Enterprise website (

http://www.hpe.com/info/qs

).

Active Health System Viewer

Active Health System Viewer (AHSV) is an online tool used to read, diagnose, and resolve server issues
quickly using AHS uploaded data. AHSV provides Hewlett Packard Enterprise recommended repair
actions based on experience and best practices. AHSV provides the ability to:

• Read server configuration information

• View Driver/Firmware inventory

• Review Event Logs

• Respond to Fault Detection Analytics alerts

• Open new and update existing support cases

Active Health System

The Active Health System monitors and records changes in the server hardware and system
configuration.

The Active Health System provides:

146

Software and configuration utilities

«
...
144
145
146
147
148
...
»

Содержание ProLiant DL180













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProLiant DL180

ShareCenter DNS-343

Бренд: D-Link Страницы: 12

Бренд: Lantronix Страницы: 6

Бренд: Lantronix Страницы: 27

AMD Opteron LS20 Type 8850

Бренд: IBM Страницы: 68

Бренд: IBM Страницы: 66

DIGITAL Server 9100 Series

Бренд: Digital Equipment Страницы: 68

SUPERSERVER 5018A-MHN4

Бренд: Supermicro Страницы: 116

UniServer R4900 G3

Бренд: H3C Страницы: 24

ProLiant ML110 Gen 10

Бренд: HPE Страницы: 5

FusionServer G8600 V7

Бренд: xFusion Digital Technologies Страницы: 112

ProLiant BL460c Gen8

Бренд: HP Страницы: 84

AirPlus G DP-G301

Бренд: D-Link Страницы: 18

Бренд: Black Box Страницы: 66

Бренд: TAG Страницы: 54

CENTRIX SV-2000-X2

Бренд: TAG Страницы: 82

Бренд: Adaptec Страницы: 6

MAP-9101-10 Series

Бренд: decrane aerospace Страницы: 30

Бренд: Gateway Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды