background image

AP-310-MNT-W3 Mount Kit

Installation Guide

0511855-01  |  

May 2018

1

Package Contents

Mount bracket

RJ45 coupler

RJ45 cable

M3 x 10mm pan head screws (4)

T6 Torx security screw

AP-310-MNT-W3

 

Mounting Template

Introduction

The AP-310-MNT-W3 mount kit offers a secure mounting solution for 310 Series Campus Access Points. 

This mount kit attaches to standard single and dual gang wall boxes, or mounts to a flat surface, such as a 

wall or ceiling.

Installing the AP-310-MNT-W3 Mount Kit

To install the mount bracket onto a flat surface, see 

Installing the AP-310-MNT-W3 to a Flat Surface

. To 

install the mount bracket onto a wall box, see 

Installing the Mount Bracket onto a Wall Box

. To install the 

mount bracket onto a European wall box, see 

Installing the Mount Bracket to a DIN or European Wall Box

.

Installing the AP-310-MNT-W3 to a Flat Surface

1. (Optional) Remove the punch-out panel on the side of the mounting bracket by pressing firmly.

2. Tape the 

AP-310-MNT-W3 Mounting Template

 flat onto the desired location, then drill holes at the 

points indicated.

The DC power plug and Kensington lock cannot be used with this mount.

This mount is not compatible with large (4.5in x 4.5in) US wiring boxes.

!

Failure to properly install the AP-310-MNT-W3 may result in damage to equipment and/or bodily injury.

!

Before installing the AP-310-MNT-W3 to any surface, ensure that the surface can support the combined weight of 

the mount kit and access point.

Содержание Aruba AP-310-MNT-W3







Отзывы: