HPE 3PAR StoreServ Скачать руководство пользователя

Страница: 128 / 174

Physical service processor LEDs, HPE ProLiant DL360 Gen10 Server

Figure 110: Physical service processor LEDs, HPE ProLiant DL360 Gen10 Server rear view

Table 39: Physical service processor LEDs, HPE ProLiant DL360 Gen10 Server

rear view

LED function

Status

State

UID LED

Blue solid

Identification is activated.

Blue flashing

System is being managed remotely.

Off

Identification is deactivated.

2R iLO 5/Standard NIC

activity LED

Green solid

Activity exists.

Green
flashing

Activity exists.

Off

No activity exists.

2L iLO 5/Standard NIC

link LED

Green solid

Link exists.

Off

No link exists.

Power supply 2 LED

Green solid

Normal

Off

One or more of the following conditions exists:

• AC power unavailable

• Power supply failed

• Power supply in standby mode

• Power supply exceeded current limit.

Power supply 1 LED

Green solid

Normal

Off

One or more of the following conditions exists:

• AC power unavailable

• Power supply failed

• Power supply in standby mode

• Power supply exceeded current limit.

128

More information

Содержание 3PAR StoreServ















































































































































































Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды

HPE 3PAR StoreServ, Руководство по обслуживанию и модернизации

Результаты поиска

Содержание 3PAR StoreServ

Отзывы:

Похожие инструкции для 3PAR StoreServ

Бренды по названию

Популярные бренды