HP StorageWorks NAS e7000 v2 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 70

background image

Beyond Initial Setup

52

NAS e7000 v2 Quick Start Guide

Cluster Installation

Installation Overview

During the installation process, both nodes will be shut down and both nodes will
be rebooted. These steps are necessary to guarantee that the data on disks that are
attached to the shared storage bus is not lost or corrupted. This can happen when
multiple nodes try to simultaneously write to the same disk that is not yet
protected by the cluster software.

Use

to determine which nodes and storage devices should be presented

during each step.

To configure the Cluster service on the HP StorageWorks NAS server, the account
must have administrative permissions on each node. Both nodes must be member
servers within the same domain.

Table 4: Power Sequencing for Cluster Installation

Step

Node

1

Node

2

Storage

Comments

Setting up

networks

On

On

Not

presented

Verify that all storage devices on

the shared bus are not presented.

Power on both nodes.

Setting up

shared disks

On

Off

Presented

Shut down both nodes. Present the

shared storage, and then power

on the first node.

Verifying Disk

Configuration

Off

On

Presented

Shut down first node, power on

second node.

Configuring the

First Node

On

Off

Presented

Shutdown all nodes; power on the

first node.

Configuring the

Second Node

On

On

Presented

Power on the second node after

the first node was successfully

configured.

Post-installation

On

On

Presented

At this point all nodes should be

on.

«
...
50
51
52
53
54
...
»

Содержание StorageWorks NAS e7000 v2







































































Отзывы:

Нет отзывов

Похожие инструкции для StorageWorks NAS e7000 v2

Бренд: NAIM Страницы: 16

SUPERSERVER 6021F

Бренд: Supermicro Страницы: 116

Бренд: Fortinet Страницы: 20

Бренд: SanDisk Страницы: 44

Бренд: Seagate Страницы: 57

ICS-G7748A Series

Бренд: Moxa Technologies Страницы: 10

Бренд: 8level Страницы: 52

Бренд: Hama Страницы: 4

Бренд: Quest Leisure Products Страницы: 20

Бренд: Ravpower Страницы: 27

Бренд: LevelOne Страницы: 11

Бренд: Planet Страницы: 2

Бренд: Quantum Страницы: 20

DiskStation DS415play

Бренд: Synology Страницы: 16

SuperServer E300-9C

Бренд: Supermicro Страницы: 113

NetVanta 300 Series

Бренд: ADTRAN Страницы: 2

FusionServer 1288H V5

Бренд: xFusion Digital Technologies Страницы: 96

Catalina KC-103

Бренд: SPAREHAND Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды