HP ProLiant XL270d Gen9 Скачать руководство пользователя страница 64

Страница: 64 / 126

Procedure

Back up all server data.

2. Power down the server

Disconnect all peripheral cables from the server front panel.

4. Remove the server from the chassis

Place the server on a sturdy, level surface.

6. Remove the access panel

Remove the Smart Storage Battery:

Disconnect the cable from the riser connector.

Pull back the release clip.

Lift the Smart Storage Battery from the holder.

To replace the component, reverse the removal procedure.

Hot-plug drive

CAUTION:

To prevent improper cooling and thermal damage, do not operate the server unless all bays are
populated with either a component or a blank.

To remove the component:

Procedure

Back up all server data on the drive.

Determine the status of the drive from the

hot-plug drive LED definitions

Remove the hot-plug drive.

Hot-plug drive

Содержание ProLiant XL270d Gen9































































































































Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы:

Похожие инструкции для ProLiant XL270d Gen9

Бренды по названию

Популярные бренды

HP ProLiant XL270d Gen9, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant XL270d Gen9

Отзывы:

Похожие инструкции для ProLiant XL270d Gen9

Бренды по названию

Популярные бренды