HP ProLiant DL60 Gen9 Скачать руководство пользователя страница 90

Страница: 90 / 127

Software and configuration utilities 90

Software and configuration utilities

Server mode

The software and configuration utilities presented in this section operate in online mode, offline mode, or

in both modes.

Software or configuration utility

Server mode

HPE iLO (on page

)

Online and Offline

Active Health System (on page

)

Online and Offline

RESTful API support for iLO (on page

)

Online and Offline

Integrated Management Log (on page

)

Online and Offline

Intelligent Provisioning (on page

)

Offline

HPE Insight Diagnostics (on page

)

Online and Offline

Erase Utility (on page

)

Offline

Scripting Toolkit for Windows and Linux (on page

)

Online

Service Pack for ProLiant (on page

)

Online and Offline

HP Smart Update Manager (on page

)

Online and Offline

HPE UEFI System Utilities (on page

)

Offline

HPE Smart Storage Administrator (on page

)

Online and Offline

FWUPDATE utility (on page

)

Offline

Product QuickSpecs

For more information about product features, specifications, options, configurations, and compatibility,

see the product QuickSpecs on the Hewlett Packard Enterprise website (

http://www.hpe.com/info/qs

HPE iLO

The iLO 4 subsystem is a standard component of ProLiant servers that simplifies initial server setup,

server health monitoring, power and thermal optimization, and remote server administration. The iLO 4

subsystem includes an intelligent microprocessor, secure memory, and a dedicated network interface.

This design makes iLO 4 independent of the host server and its operating system.
iLO 4 enables and manages the Active Health System (on page

) and also features Agentless

Management. All key internal subsystems are monitored by iLO 4. If enabled, SNMP alerts are sent

directly by iLO 4 regardless of the host operating system or even if no host operating system is installed.
Using iLO 4, you can do the following:

•

Access a high-performance and secure Integrated Remote Console to the server from anywhere in

the world if you have a network connection to the server.

•

Use the shared .NET Integrated Remote Console to collaborate with up to four server administrators.

•

Remotely mount high-performance Virtual Media devices to the server.

•

Securely and remotely control the power state of the managed server.

Содержание ProLiant DL60 Gen9
































































































































Результаты поиска

Содержание ProLiant DL60 Gen9

Отзывы:

Похожие инструкции для ProLiant DL60 Gen9

Бренды по названию

Популярные бренды

HP ProLiant DL60 Gen9, Руководство пользователя

Результаты поиска

Содержание ProLiant DL60 Gen9

Отзывы:

Похожие инструкции для ProLiant DL60 Gen9

Бренды по названию

Популярные бренды