HP ProCurve 8116fl Скачать руководство пользователя страница 82

Страница: 82 / 134

Repla

g Hard

Replacing Hardware

Installing or Removing Transceivers and Connecting Cables

Removing Transceivers

To remove a transceiver:

1. Disconnect the network cable from the transceiver before removing it

from the module.

2. If your transceiver has a wire bail, lower the bail and then use the bail to

pull the transceiver from the slot.

If your transceiver does not have a bail, pull the transceiver straight out.

(Optional) Installing an Optical Media Converter

An optical media converter (OMC) can be installed into the copper transceiver
to enable a fiber-optic cable connection.

N o t e

You can install a media converter without having to power off the switch. Use
only the ProCurve supported media converter (see

page 1-5

To install a media converter:

1. Connect the media converter to the copper transceiver port until it clicks

into place.

Extractor Handle

Copper Transceiver

Optical Media Converter

LED

2. A multimode fiber ribbon cable can now be installed, see

page 4-11

N o t e o n L E D

The OMC has a single bi-color LED to indicate Power and Link. The LED
goes Orange when it has power but no link, and goes Green when a link
is established with the other end of a 12-strand flat MTP cable.

4-10

Содержание ProCurve 8116fl







































































































































Результаты поиска

Содержание ProCurve 8116fl

Отзывы:

Бренды по названию

Популярные бренды

HP ProCurve 8116fl, Руководство по установке и началу работы

Результаты поиска

Содержание ProCurve 8116fl

Отзывы:

Бренды по названию

Популярные бренды