manualshive.com logo in svg

HP ProCurve 8116fl, Руководство по установке и началу работы

Поделиться
Скачать
HP ProCurve 8116fl Скачать руководство пользователя страница 83

Replacing Hardware 

Installing or Removing Transceivers and Connecting Cables 

To remove a media converter: 

1.   Disconnect the network cable from the converter before removing it 

from the module. 

2.   Pull the extractor handle to remove the converter from the transceiver. 

Connecting Network Cables to Transceiver Ports 

To install fiber-optic cable: 

■

  

Aligning the cable connectors with the slots of the transceiver ports,  press 
the cable connector into the transceiver port until it snaps into place. 

Optical Media Converter 

Fiber Optic Transceiver 

N o t e    

To ensure proper transmit/receive connections, make sure the transmit 
from one device is connected to the receive of the other device. 

To install copper cable: 

1.   Insert the copper cable connector into the copper transceiver port. 

2.   Push the handle forward to engage the locking mechanism. 

Copper Transceiver 

Handle 

R

e

pl

a

c

in

g H
a

rd

wa
re 

4-11 

Содержание ProCurve 8116fl







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды