HP photosmart 850 страница 96 Скачать руководство пользователя

Страница: 96 / 136

PPPoE server commands

Support for the commands in this chapter depends on the device model. For more information, see

About

the Command References for HP Unified Wired-WLAN Products

display pppoe-server session

Use

display pppoe-server

session

to display information about PPPoE sessions on a device operating as

a PPPoE server.

Syntax

display pppoe-server

session all

[

{

begin

exclude

include

}

regular-expression

]

Views

Any view

Default command level

1: Monitor level

Parameters

all

: Displays all the information about PPPoE sessions.

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Examples

# Display all the information about PPPoE sessions. (Assume the current device is operating as a PPPoE

server.)

<Sysname> display pppoe-server session all

Total PPPoE Session(s): 2

SID Intf State OIntf RemMAC LocMAC

1 Virtual-Template1:0 UP Vlan2 00e015004100 00e014004300

2 Virtual-Template2:0 UP Vlan2 00e016004100 00e015004300

Table 21

Command output

Field Description

SID

PPPoE session ID.

Intf Virtual-template

interface.

State

PPPoE session state.

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды