HP photosmart 850 страница 84 Скачать руководство пользователя

Страница: 84 / 136

link-aggregation load-sharing mode

Use

link-aggregation load-sharing mode

to configure the global or group-specific link-aggregation load

sharing mode.
Use

undo link-aggregation load-sharing mode

to restore the default.

Syntax

link-aggregation load-sharing mode

{

destination-ip

destination-mac

source-ip

source-mac

} *

undo link-aggregation load-sharing mode

Default

The global or group-specific link-aggregation load sharing mode is source and destination MAC

addresses.

Views

System view, Layer 2 aggregate interface view

Default command level

2: System level

Parameters

destination-ip

: Load shares traffic based on destination IP addresses.

destination-mac

: Load shares traffic based on destination MAC addresses.

source-ip

: Load shares traffic based on source IP addresses.

source-mac

: Load shares traffic based on source MAC addresses.

Usage guidelines

The load sharing mode that you configure overwrites the previous mode.

Examples

# Configure the global link-aggregation load sharing mode to load share packets based on source MAC

addresses and destination MAC addresses.

<Sysname> system-view

[Sysname] link-aggregation load-sharing mode source-mac destination-mac

# Configure Layer 2 aggregation group 1 to load share packets based on destination MAC addresses.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation load-sharing mode destination-mac

link-aggregation mode

Use

link-aggregation mode dynamic

to configure an aggregation group to operate in dynamic

aggregation mode.
Use

undo link-aggregation mode

to restore the default.

Syntax

link-aggregation mode dynamic
undo link-aggregation mode

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды