background image

Upgrading and Servicing Guide    

1

 

Safety Information 

This product has not been evaluated for connection 
to an “IT” power system (an AC distribution system 
with no direct connection to earth, according to 
IEC 60950). 

 

 

WARNING: Please read “Safety 
Information” in your 

Warranty and 

Support Guide 

before installing and 

connecting your system to the electrical 
power system. 

 

The 

Upgrading and Servicing Guide

 provides 

instructions on how to remove and replace hardware 
components of your PC. 

To open the lid of your PC, gently push down on the 
lid before sliding it back. 

 

 

 

Opening and Closing the PC 

Preparing the PC 

Before you upgrade any component in your PC, you 
need to prepare the PC so that you can safely handle 
it and the components. 

Read the following items before attempting to upgrade 
or service the PC. 

• 

These procedures assume familiarity with the 
general terminology associated with personal 
computers and with the safety practices and 
regulatory compliance required for using and 
modifying electronic equipment. 

• 

Write down and save the system model and serial 
numbers, all installed options, and other 
information about the system. It will be easier to 
consult this information than to open up and 
examine the PC. 

• 

HP recommends that you use an antistatic wrist 
strap and a conductive foam pad when working on 
the system. 

 

 

WARNING: Always disconnect the modem 
cord from the telephone system, and then 
disconnect the PC from the power source 
before removing the front and side panels 
of the PC. Failure to do so before you 
open the PC or do any procedures can 
result in personal injury or equipment 
damage. 

 

Содержание Pavilion w1100 - Desktop PC

















Отзывы: