background image

-10-

 

FCC STATEMENT

 

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful 

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction guide, may cause 
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.  If this 

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and the receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

 

Consult a service representative for help. 

 

Caution: 
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this 
equipment.  Shielded interface cable, if any, must be used in order to comply with emission limits. 

 
Properly shielded and grounded cables and connectors must be used in order to comply with FCC emission limits. Hewlett-Packard is not responsible 

for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or 
modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.  
 

For regulatory compliance information only, contact: 
 

Hardware Quality Eng. Manager 
Hewlett-Packard Company - CPC 
10500 Ridgeview Court 

Cupertino, CA95014 
 
Telephone: 1(408) 343-5000 

 

 
 

Tested To Comply With FCC Standards 
FOR HOME OR OFFICE USE 

 
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de classe B est conforme à la norme NMB-003 du Canada. 

Содержание MORFB1UO












Отзывы: