HP ML350 - ProLiant - G2 Скачать руководство пользователя страница 67

Страница: 67 / 78

Component identification 67

Item Description

Status

System fan 1

Amber = Fan is not installed or has failed
Off = Rear fan is functioning

Online spare

memory

Amber = Online spare memory is in use due to

memory failover
Off = Normal operation

15 Memory

mode

Green = System is in online spare memory

mode
Off = Normal operation

System LEDs and internal health LED combinations

When the internal health LED on the front panel illuminates either amber or red, the server is experiencing

a health event. Combinations of illuminated system LEDs and the internal health LED indicate system

status.
The front panel health LEDs indicate only the current hardware status. In some situations, HP SIM may

report server status differently than the health LEDs because the software tracks more system attributes.

System LED and color

Internal health LED

color

Status

Processor failure,

socket

(amber)

Red

One or more of the following conditions may exist:

•

Processor in socket

has failed.

•

Processor in socket

failed over to the second

processor.

•

Processor

is not installed in the socket.

•

Processor

is not supported.

•

Processor heatsink is not attached properly.

Amber

Processor in socket

is in a pre-failure condition.

Processor failure, both

sockets (amber)

Red

Processor types are mismatched.

PPM failure (amber)

Red

•

PPM has failed.

•

PPM is not installed, but the corresponding processor

is installed.

FBDIMM failure, slot

(amber)

Red

•

FBDIMM in slot

has failed.

•

FBDIMM in slot

is an unsupported type, and no

valid memory exists in another bank.

Amber

•

FBDIMM in slot

has reached single-bit correctable

error threshold.

•

FBDIMM in slot

is in a pre-failure condition.

•

FBDIMM in slot

is an unsupported type, but valid

memory exists in another bank.

Overtemperature

(amber)

Red

•

The Health Driver has detected a cautionary

temperature level.

•

The server has detected a hardware critical

temperature level.

Fan (amber)

Red

The minimum fan requirements are not being met. Fan has

failed.

Содержание ML350 - ProLiant - G2















































































Результаты поиска

Содержание ML350 - ProLiant - G2

Отзывы:

Похожие инструкции для ML350 - ProLiant - G2

Бренды по названию

Популярные бренды

HP ML350 - ProLiant - G2, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ML350 - ProLiant - G2

Отзывы:

Похожие инструкции для ML350 - ProLiant - G2

Бренды по названию

Популярные бренды