HP J4861A Скачать руководство пользователя | Manualshive

Страница: 70 / 94

background image

Switch Ports and Network Cables

Cables

Twisted-Pair

10 Mbps Operation

Category 3, 4, or 5 100-ohm differential unshielded twisted-
pair (UTP) or shielded twisted-pair (STP) cable, complying
with IEEE 802.3 Type 10Base-T specifications, fitted with
RJ-45 connectors.

100 Mbps Operation

Category 5 100-ohm differential UTP or STP cable,
complying with IEEE 802.3u 100Base-TX specifications,
fitted with RJ-45 connectors.

1000 Mbps Operation

Category 5 100-ohm differential 4-pair UTP or STP cable,
complying with IEEE 802.3ab 1000Base-T specifications,
fitted with RJ-45 connectors—Category 5E or better is
recommended.

(please see “Note on 1000Base-T Cable Requirements”,
below)

Note on 1000Base-T Cable Requirements.

The Category 5 networking

cables that work for 100Base-TX connections should also work for
1000Base-T, as long as all four-pairs are connected. But, for the most robust
connections you should use cabling that complies with the Category 5E
specifications, as described in Addendum 5 to the TIA-568-A standard (ANSI/
TIA/EIA-568-A-5).

Because of the increased speed provided by 1000Base-T (Gigabit-T), network
cable quality is more important than for either 10Base-T or 100Base-TX. Site
cabling that is being used to carry 1000Base-T networking must comply with
the IEEE 802.3ab standards. In particular, the cabling must pass tests for
Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT).
Additionally, unlike the cables for 100Base-TX, the 1000Base-T cables must
pass tests for Equal-Level Far-End Crosstalk (ELFEXT), Multiple Disturber
ELFEXT, and Return Loss.

When testing your cabling, be sure to include the patch cables that connect
the switch and other end devices to the patch panels on your site. The patch
cables are frequently overlooked when testing cable and they must also
comply with the cabling standards.

Sw

it

ch Ports and

Netw

ork

Cabl

es

B-2

«
...
68
69
70
71
72
...
»

Содержание J4861A































































































Отзывы:

Нет отзывов

Похожие инструкции для J4861A

Бренд: JB Systems Light Страницы: 15

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

Бренд: Audio Authority Страницы: 12

EX ZS 92 S 22 VD F

Бренд: steute Страницы: 28

SwitchMan USB-Combo SW2

Бренд: Raritan Страницы: 2

Signature ANTENNA GENIUS 8x2 v2 PLUS

Бренд: 4O3A Страницы: 57

Бренд: Conceptronic Страницы: 7

FortiSwitch 424E Series

Бренд: Fortinet Страницы: 11

SmartSwitch SBU128

Бренд: Cabletron Systems Страницы: 76

LMP-0602 24-V2 Series

Бренд: ANTAIRA Страницы: 2

Бренд: Key Digital Страницы: 20

Бренд: Kramer Страницы: 29

Бренд: Niles Страницы: 2

Бренд: Led Control Страницы: 22

BZ-UHD-88M100-ARC

Бренд: BZB Gear Страницы: 42

Бренд: DataParts Страницы: 4

Бренд: Pliant Страницы: 49

Бренд: Datavideo Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды