HP J2600A Скачать руководство пользователя страница 28

Страница: 28 / 138

Network Port Connections

The HP AdvanceStack 10Base-T Hubs have the following network ports:

twisted-pair

ThinLAN (BNC)
AUI/Xcvr Slot

This section describes how to connect cables to these ports.

Twisted-pair Connections

Twisted-pair connections can be made through the 12-port hub’s built-in
RJ-45 jacks and the 24 and 48-port hubs’ 50-pin telco connectors, used
either directly or with a 50-pin/RJ-45 Adapter (J2605-61001).

Using the 50-pin/RJ-45 Adapter:

To install the 50-pin/RJ-45 Adapter

(J2605-61001) on the 24 and 48-port hubs’ telco connectors:

1. Insert the hook on the back of the adapter into the slot on the hub’s

face.

2. Pivot the adapter and press it onto the telco connector.

3. Make sure the hook is in the hub’s slot, then secure the adapter to

the hub using the thumb screw.

Do not overtighten the screw

slot in the hub

50-pin telco
connector

insert hook

in slot

press adapter

onto telco

connector

secure adapter

with thumb screw

Installing the

vanceStack Hubs

Installing the HP AdvanceStack 10Base-T Hubs

1-14

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание J2600A











































































































































Результаты поиска

Содержание J2600A

Отзывы:

Бренды по названию

Популярные бренды

HP J2600A, Инструкция по установке и справочник

Результаты поиска

Содержание J2600A

Отзывы:

Бренды по названию

Популярные бренды