HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 46

Страница: 46 / 306

Related commands

•

broadcast-suppression

•

multicast-suppression

virtual-cable-test

IMPORTANT:

•

Fiber ports do not support this command.

•

If the link of an Ethernet port is up, testing its cable connection will cause the link to go down and

then come up.

Use

virtual-cable-test

to test the cable connection of an Ethernet interface and display the test

results.

Syntax

virtual-cable-test

Views

Layer 2 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

If the link of an Ethernet interface is up, testing its cable connection will cause the link to go down and
then up.

The test result is for reference only. The cable length detection error is up to 5 m (about 16 ft).

If a test item is not available, a hyphen (-) is displayed.

Examples

# Test the cable connection of GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] virtual-cable-test

Cable status: abnormal(open), 140 metre(s)

Pair Impedance mismatch: -

Pair skew: - ns

Pair swap: -

Pair polarity: -

Insertion loss: - db

Return loss: - db

Near-end crosstalk: - db

Table 8 Command output

Field Description

Cable status

Cable status:

•

Normal

—The cable is in good condition.

•

Abnormal

—The cable is abnormal.

•

Abnormal (open)

—An open circuit is detected.

•

Abnormal (short)

—A short circuit is detected.

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды