HP FlexNetwork 5130 HI series Скачать руководство пользователя страница 176

Страница: 176 / 306

168

Field Description

interface brief

command, this field displays the complete

interface description.

Bandwidth

Expected bandwidth of the VLAN interface.

Maximum transmission unit

MTU of the VLAN interface.

Internet protocol processing : Disabled

The interface cannot process IP packets. This field is displayed
when the interface is not configured with an IP address.

Internet address: 192.168.1.54/24
(primary)

The primary IP address of the interface is 192.168.1.54/24. This
field is displayed only when the primary IP address is configured
for the interface.

IP packet frame type

Framing format of the sent IPv4 packets.

hardware address

MAC address of the VLAN interface.

IPv6 packet frame type

Framing format of the sent IPv6 packets.

Brief information on interfaces in route
mode

Brief information about Layer 3 interfaces.

Link: ADM - administratively down; Stby
– standby

Link layer state of the interface:

•

ADM

—The interface has been administratively shut down.

To bring up the interface, use the

undo shutdown

command.

•

Stby

—The interface is operating as a backup interface.

Protocol: (s) - spoofing

The protocol attribute of an interface includes the spoofing flag
(the letter

in parentheses) when the following conditions exist:

•

The data link layer protocol state of an interface is shown as

•

Its link is an on-demand link or is not present.

Interface

Abbreviated interface name.

Link

Physical link state of the interface:

•

—The physical link of the interface is up.

•

DOWN

—The physical link of the interface is down.

•

ADM

—The interface has been administratively shut down.

To bring up the interface, use the

undo shutdown

command.

•

Stby

—The interface is operating as a backup interface.

Protocol

Data link layer state of the interface:

•

—The data link layer of the interface is up.

•

DOWN

—The data link layer of the interface is down.

•

UP(s)

—The data link layer of the interface is spoofing up.

This state is available for on-demand link setup applications.
This state enables the device to initiate an on-demand link
setup when a link is not present.

Primary IP

Primary IP address of the interface.

display vlan

Use

display

vlan

to display VLAN information.

Содержание FlexNetwork 5130 HI series



















































































































































































































































































































Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды

HP FlexNetwork 5130 HI series, Справочник по командам

Результаты поиска

Содержание FlexNetwork 5130 HI series

Отзывы:

Похожие инструкции для FlexNetwork 5130 HI series

Бренды по названию

Популярные бренды