manualshive.com logo in svg

HP F1523 - Pavilion - 15" LCD Monitor, Руководство по обслуживанию

Поделиться
Скачать
HP F1523 - Pavilion - 15

Page 4

vf15 / FP15 / f1523 / FP5315

2.

Inverter

This unit operates on an output voltage of 15V from power source.

2.1

Regulator: Q101 get a +5VDC for I101 power supply.

2.2

UVP: Q106 turns off when the Vin is under 10V. Then pin 3 of I101 is pulled low and inverter off immediately.

That is the under voltage protection.

2.3

Control IC: I101 (OZ960S)

2.3.1 Enable : When pin 3 of I101 is over 1.5V, I101 works. If it is under 1.5V, I101 turns off.

2.3.2 OSC: When I101 enabled, R108/C115 (pin 17/pin18 of I101) determine the operating frequency.

2.3.3 SST: C104 (pin 4 of I102) provides soft start function.

2.3.4 Ignition: R109 (pin 8 of I101) provides higher operating frequency for more striking voltage until regulation of

feedback of lamp current. C103 (pin 1 of I101) determine the striking time.

2.3.5 Dimming control: The divided voltage of R106/R105/R104 control the duty pulse of burst-mode to drive Q105

and perform a wide dimming control for the CCFL. The burst-mode frequency is determined by C116.

2.3.6 Regulation: Pin 9/pin 10 of I101 provide regulation of the CCFL current from feedback. The non-inverting reference

(pin 10 of I101) is at 1.25V nominal.

2.3.7 Protection: Open-lamp protection in the ignition period is provided through both pin1 and pin 2 of I101.

Removal of the CCFL during normal operation will trigger Q107 to turns on and shuts off the inverter. This is latch

function.

2.3.8 Output drivers: The configuration  prevents any shoot-through  issue associated  with bridge-type power

conversion applications. Adjusting the overlap conduction between I102 P-MOSFET and I103 N-MOSFET,

           I102 N-MOSFET and I103 P-MOSFET, the CCFL current regulation is achieved.

2.4

Full-bridge swit ching/Transformer: I102/I103 /C123/I104/I105/C137/C125/T101/T102 compose full-bridge swit ching

to convert DC into AC for driver the CCFL.

2.5

Detection: C124/C125/C126 detect the output voltage and ensure a rated voltage by pin2 of I101. Q108/Q109

ensure not a open-lamp.

2.6

Feedback: D119/R123/D120 sense the lamp current for negative feedback and regulation.

Inverter Circuit

VCC

Regulator

U.V.P.

Enable

OSC

SST

Dimming

control

Output driver

Protection

Ignition

Regulation

Control IC : OZ960

ON / OFF

Full-bridge switching

Transformer

Lamp

Feed back

Detection

Brightness

control

VDD

Содержание F1523 - Pavilion - 15" LCD Monitor






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды