HP Compaq dx2818 Microtower Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 57

background image

9.

Slide the drive in through the front of the chassis (1) until the screw holes on the drive are aligned
with the screw holes on the drive cage and install the two M3 metric retainer screws (2) as shown
in the illustration below.

NOTE:

Extra drive retainer screws are provided on the interior of the front bezel if needed. The

M3 metric retainer screws for diskette drives or media card readers are black. Refer to

Installing

Additional Drives on page 23

for an illustration of the retainer screws location.

Figure 2-24

Installing a 3.5-inch Device (Diskette Drive Shown)

10.

Connect the appropriate drive cables:

a.

If installing a diskette drive, connect the power and data cables to the rear of the drive and
connect the other end of the data cable to the connector on the system board labeled FLOPPY.

b.

If installing a media card reader, connect the USB cable from the media card reader to the
USB connector on the system board labeled F_USB2.

NOTE:

Refer to

System Board Drive Connections on page 24

for an illustration of the system

board drive connectors.

11.

Replace the front bezel and access panel.

12.

Reconnect the power cord and turn on the computer.

13.

Lock any security devices that were disengaged when the access panel was removed.

Removing an Internal 3.5-inch Hard Drive

NOTE:

Before you remove the old hard drive, be sure to back up the data from the old hard drive so

that you can transfer the data to the new hard drive. Also, if you are replacing the primary hard drive,
make sure you have created a Recovery Disc Set to restore the operating system, software drivers, and
any software applications that were preinstalled on the computer. If you do not have this CD set, select

Start

>

HP Backup and Recovery

and create it now.

1.

Remove/disengage any security devices that prohibit opening the computer.

2.

Remove all removable media, such as diskettes or compact discs, from the computer.

30

Chapter 2 Hardware Upgrades

ENWW

«
...
34
35
36
37
38
...
»

Содержание Compaq dx2818 Microtower


























































Отзывы:

Нет отзывов

Похожие инструкции для Compaq dx2818 Microtower

Бренд: IBM Страницы: 66

Decision Mate V

Бренд: NCR Страницы: 426

Бренд: Advantech Страницы: 50

ARK-3531 Series

Бренд: Advantech Страницы: 84

Бренд: Acer Страницы: 61

Бренд: Acer Страницы: 24

Бренд: Acer Страницы: 32

Бренд: Acer Страницы: 32

Бренд: Acer Страницы: 29

Aspire 7100 System

Бренд: Acer Страницы: 108

Бренд: Acer Страницы: 108

Бренд: Acer Страницы: 130

Altos G330 Series

Бренд: Acer Страницы: 134

Aspire 1820PT Series

Бренд: Acer Страницы: 216

Бренд: Acer Страницы: 114

Бренд: Acer Страницы: 130

Бренд: Acer Страницы: 121

Бренд: Acer Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды