HP Compaq dx2700 Microtower and Small Form Factor Скачать руководство пользователя страница 63

Страница: 63 / 107

6–26

431672-001

Service Reference Guide

Removal and Replacement Procedures— Microtower (MT)/Small Form Factor (SFF) Chassis

6.9 Front I/O Panel Housing Assembly - MT chassis

1. Prepare the computer for disassembly (

Section 6.1, “Preparation for Disassembly”

2. Remove the access panel and rotate the computer so the system board is parallel to the table

to make it easier to work on (

Section 6.1, “Preparation for Disassembly”

3. Disconnect two attaching cables from the system board: the power switch/LED cable, and

the front USB cable.

4. Remove the two screws

that secure the housing to the chassis and then pull the housing

away from the chassis.

To install the housing assembly, reverse the removal procedures.

The installtion method for SFF is similar to MT.

Содержание Compaq dx2700 Microtower and Small Form Factor












































































































Результаты поиска

Содержание Compaq dx2700 Microtower and Small Form Factor

Отзывы:

Похожие инструкции для Compaq dx2700 Microtower and Small Form Factor

Бренды по названию

Популярные бренды

HP Compaq dx2700 Microtower and Small Form Factor, Руководство по обслуживанию и справочник

Результаты поиска

Содержание Compaq dx2700 Microtower and Small Form Factor

Отзывы:

Похожие инструкции для Compaq dx2700 Microtower and Small Form Factor

Бренды по названию

Популярные бренды