HP Compaq d530 SFF Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 79

HP Compaq d530 SFF Скачать руководство пользователя страница 11

Hardware Reference Guide

www.hp.com

2-1

2

Hardware Upgrades

Serviceability Features

This computer includes features that make it easy to upgrade and
service. No tools are needed for most of the installation procedures
described in this chapter.

Warnings and Cautions

Before performing upgrades be sure to carefully read all of the
applicable instructions, cautions, and warnings in this guide.

Å

WARNING:

To reduce the risk of personal injury from electrical shock

and/or hot surfaces, be sure to disconnect the power cord from the wall
outlet, and allow the internal system components to cool before touching.

Å

WARNING:

To reduce the risk of electrical shock, fire, or damage to the

equipment, do not plug telecommunications/telephone connectors into
the network interface controller (NIC) receptacles.

Ä

CAUTION:

Static electricity can damage the electronic components of

the computer or optional equipment. Before beginning these procedures,
ensure that you are discharged of static electricity by briefly touching a
grounded metal object. Refer to

Appendix F, “Electrostatic Discharge”

in

this guide for additional information on preventing electrostatic discharge.

Ä

CAUTION:

Before removing the computer access panel ensure that the

computer is turned off and that the power cord is disconnected from
the electrical outlet.

«
...
9
10
11
12
13
...
»

Содержание Compaq d530 SFF
















































































Отзывы:

Нет отзывов