HP Compaq d530 MT Скачать руководство пользователя | Manualshive

Страница: 55 / 80

background image

Hardware Reference Guide

www.hp.com

B–1

B

PATA Hard Drive Installation Guidelines

✎

For more information about Serial ATA (SATA) devices, refer to the
white paper “Implementation of Serial ATA on HP Business
Desktops”. The white paper is located at

www.hp.com/support

.

Using the Cable-Select Feature with Parallel ATA
(PATA) Devices

Optional drives are available from HP in kits that include a special
drive cable. The configuration of the drive employs a cable-select
feature that identifies the drive as device 0 (primary drive) or device 1
(secondary drive).

Device 1 is the drive connected to the cable’s middle connector.
Device 0 is the drive connected to the cable’s end connector (applies
only to 80-conductor ATA cables). See

“Guidelines for Installing

PATA Drives”

in this appendix for an example of an PATA cable.

HP hard drives ship with jumpers preset to cable-select mode;
therefore, no jumper setting changes on the existing or optional drives
are required. If you purchase a third-party hard drive, refer to the
documentation included with the kit to ensure proper installation and
configuration of cables.

✎

If installing a second device on the primary controller, you must use
an 80-conductor PATA cable for optimal performance. This cable is
standard on select models.

Guidelines for Installing PATA Drives

When installing additional drives, follow these guidelines:

«
...
53
54
55
56
57
...
»

Содержание Compaq d530 MT

















































































Отзывы:

Нет отзывов

Похожие инструкции для Compaq d530 MT

PT-970 A Series

Бренд: Contec Страницы: 77

Бренд: Fluidwell Страницы: 52

Бренд: Acer Страницы: 43

Бренд: Acer Страницы: 72

Predator PO3-640

Бренд: Acer Страницы: 27

Predator G Series

Бренд: Acer Страницы: 52

Бренд: Acer Страницы: 39

Predator PO3-600

Бренд: Acer Страницы: 30

Predator P09-600

Бренд: Acer Страницы: 31

PREDATOR ORION 3000 600 I9100

Бренд: Acer Страницы: 30

N260G U2802CP - Veriton - 2 GB RAM

Бренд: Acer Страницы: 22

Бренд: Acer Страницы: 142

Predator HELIOS 300

Бренд: Acer Страницы: 83

Бренд: Acer Страницы: 102

Бренд: Acer Страницы: 126

Бренд: Acer Страницы: 99

Бренд: Acer Страницы: 143

Бренд: Acer Страницы: 131

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды