HP BCDVideo BCD108 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 162

background image

Software and configuration utilities 125

Service Pack for ProLiant

The SPP is a comprehensive systems software (drivers and firmware) solution delivered as a single
package with major server releases. This solution uses SUM as the deployment tool and is tested on all
supported ProLiant servers including HPE ProLiant Gen8 and later servers.

SPP allows the following operating modes:

•

Online mode – The installation occurs while the host processor is running in the normal server
environment.

•

Offline mode – Boots a small Linux kernel and enables updates to occur on a single server.

For more information or to download SPP, see one of the following pages on the Hewlett Packard
Enterprise website:

•

Service Pack for ProLiant download page (

http://www.hpe.com/servers/spp/download

•

Smart Update: Server Firmware and Driver Updates page
(

http://www.hpe.com/info/SmartUpdate

Smart Update Manager

SUM is a product used to install and update firmware, drivers, and systems software on ProLiant servers.
SUM provides a GUI, a command-line scriptable interface, and an interactive command-line scriptable
interface. The interfaces allow you to deploy firmware, drivers, and software for supported nodes.

For more information about SUM, see the product page on the Hewlett Packard Enterprise website
(

http://www.hpe.com/servers/hpsum

To download SUM, see the Hewlett Packard Enterprise website
(

http://www.hpe.com/servers/hpsum/download

To access the

Smart Update Manager User Guide

, see the Hewlett Packard Enterprise Information

Library (

http://www.hpe.com/info/sum-docs

UEFI System Utilities

The UEFI System Utilities is embedded in the system ROM. The UEFI System Utilities enable you to
perform a wide range of configuration activities, including:

•

Configuring system devices and installed options

•

Enabling and disabling system features

•

Displaying system information

•

Selecting the primary boot controller

•

Configuring memory options

•

Selecting a language

•

Launching other preboot environments such as the Embedded UEFI Shell and Intelligent
Provisioning

For more information, see the UEFI System Utilities user guide for your product on the Hewlett Packard
Enterprise website (

http://www.hpe.com/info/UEFI/docs

To access mobile-ready online help for the UEFI System Utilities and UEFI Shell, scan the QR code at the
bottom of the screen. For on-screen help, press the

F1

key.

«
...
123
124
125
126
127
...
»

Содержание BCDVideo BCD108



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCDVideo BCD108

Бренд: Xblue Networks Страницы: 148

Бренд: Supero Страницы: 112

Бренд: Buffalo Страницы: 80

ZENWORKS PATCH MANAGEMENT 6.4 SP2 - SERVER

Бренд: Novell Страницы: 390

Бренд: W&T Страницы: 228

Бренд: Olive Страницы: 44

Бренд: Belkin Страницы: 2

SC450NX - Server Platform - 0 MB RAM

Бренд: Intel Страницы: 200

Бренд: Antrica Страницы: 68

Бренд: netAlly Страницы: 2

Бренд: Kramer Страницы: 2

Бренд: Advantech Страницы: 6

Бренд: TAG Страницы: 72

Бренд: Antrica Страницы: 57

Бренд: Intel Страницы: 80

Бренд: Intel Страницы: 97

Бренд: Intel Страницы: 108

SE7320SP2 - 800MHZ Ecc Ddr Xeon

Бренд: Intel Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды