HP A-MSR20 Скачать руководство пользователя

Страница: 34 / 88

RTD59895



Symptom: Period of time, The SIC-1T1-F card can’t receive and send packets, and the
interface queue is plugged up.



Condition: The POE router is inserted into FSW-POE card and SIC-1T1-F card.

RTD60199



Symptom: The SNMP OID hh3cCfgLogTerminalUser value is error.



Condition: None.

Resolved problems in CMW520-R2209

RTD59161



Symptom: When transmits some UDP packets, the router will reboot abnormally.



Condition: The router runs NAT function, and there are several NAT outbound
commands at the interface of the router.

RTD58793



Symptom: The result of NQA was inaccurate.



Condition: Run NQA function in the Multilink PPP link with several physical interfaces.

RTD58598



Symptom: The line protocol status of the async interface is always down.



Condition: The aysnc interface of the router works at flow mode.

RTD59306



Symptom: OSPF Area 0 ABR does not generate default to stub when no neighbor in
Area 0.



Condition: Run OSPF protocol in the router.

Resolved problems in CMW520-R2207P45

RTD58789



Symptom: If the router received challenge more than 16 bytes, the PPP CHAP
authentication failed.



Condition: The interface of the router set PPP protocol and CHAP authentication.

RTD58508



Symptom: The router can’t identify the INARP packets with filled information, so the
router failed to parse the IP address.



Condition: None.

Содержание A-MSR20

























































































Результаты поиска

Содержание A-MSR20

Отзывы:

Похожие инструкции для A-MSR20

Бренды по названию

Популярные бренды

HP A-MSR20, Руководство пользователя

Результаты поиска

Содержание A-MSR20

Отзывы:

Похожие инструкции для A-MSR20

Бренды по названию

Популярные бренды