HP 8920A Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 658

background image

134

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

The CALL CONTROL Screen

Order

This field is used to send an order on the forward voice channel to the Mobile
Station. A mobile station must be actively connected on a voice channel to the
Test Set (that is, the

Connect

annunciator must be lit) before you can send an

order to a mobile station.

The

Order

field is a one-of-many selection field. To send an order to the mobile

station, select the

Order

field. A list of choices is displayed. Select the desired

order from the

Choices:

menu. The following orders are available:

Change Power to Power Level 0 - 7

•

Maintenance (put the mobile station in maintenance mode)

Alert (alert the mobile station)

MRI (mobile reported interference) request (

NAMPS

system type only)

Once the selection is made a mobile station control message is sent to the mobile
station. The

Access

annunciator will light momentarily while the Test Set is

sending the mobile station control message.

Pwr Lvl:

Pwr Lvl:

is divided into two fields:

•

The left-hand field displays the mobile station’s output power level assigned to the
voice channel being used by the Test Set and the mobile station. A numeric value is
displayed only when a mobile station is actively connected on a voice channel (that is,
the

Connect

annunciator must be lit). A “-” is displayed if a mobile station is not

actively connected on a voice channel.

•

The right-hand field (highlighted field) is used to enter the Voice Mobile Attenuation
Code (VMAC). The VMAC determines the mobile station’s power level to be used on
the voice channel (See

field description, on page 125

for more information

about the voice channel).

Page

This field is used to initiate a page to the mobile station that is connected to the
Test Set. The Test Set must be in the active state (that is,

Active

annunciator

must be lit) and the

MS Id

information must be entered before you can attempt to

page the mobile station.

«
...
132
133
134
135
136
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: Falcon Страницы: 52

Бренд: Parata Страницы: 40

Бренд: Makita Страницы: 60

Бренд: JB-Lighting Страницы: 60

Бренд: Bahco Страницы: 9

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: Gardigo Страницы: 24

Бренд: Gardner Bender Страницы: 8

Бренд: Garantia Страницы: 4

Бренд: NARIKA Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: Gardigo Страницы: 32

Бренд: Patiova Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды