HP 8920A Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 658

background image

123

Chapter 6, Call Processing Subsystem

The CALL CONTROL Screen

The CALL CONTROL screen is the primary Call Processing Subsystem screen. It
contains the most often used call processing configuration and command fields.

Figure 18 on page 122

shows the CALL CONTROL screen for NAMPS.

The top right-hand portion of the CALL CONTROL screen is used to display the
following information:

•

decoded data messages received from the mobile station on the reverse control channel
or the reverse voice channel

•

modulation quality measurements made on the mobile station’s RF carrier while on a
voice channel

•

raw data message bits, displayed in hexadecimal format, received from the mobile
station on the reverse control channel or reverse voice channel when a decoding error
occurs

The type of information to be displayed is selected using the

Display

field. Refer

to the

field description, on page 127

for further information.

[] Access

When lit, the

Access

annunciator indicates the Test Set is signaling the mobile

station with command information on the forward voice channel. This is a
transitory state.

The Test Set’s speaker is turned off when in the access state. This is done to
eliminate any possible audio feedback which may occur if the mobile station’s
microphone is open.

Active

This field is used to turn on the forward control channel of the Test Set or to force
a return to the active state from any other state (register, page, access, connect). If
the forward control channel of the Test Set is already active, selecting this field
will deactivate and then reactivate the control channel.

[] Active

When lit, the

Active

annunciator indicates the control channel of the Test Set is

turned on.

If this annunciator is lit, the base station is transmitting system parameter
overhead messages on the assigned control channel. If the annunciator is not lit,
the base station is not active.

«
...
121
122
123
124
125
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: ACS Страницы: 56

Бренд: Backyard Discovery Страницы: 51

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Бренд: Bard Страницы: 144

Бренд: GALBIATI Страницы: 8

Бренд: Vahva Jussi Страницы: 9

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: G-Systems Страницы: 60

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

9NP-B7524 Series

Бренд: Nautilus Страницы: 2

Be strong NS 700X

Бренд: Nautilus Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды