HP 85106D Скачать руководство пользователя страница 79

Страница: 79 / 244

2-34

HP 85106D mm-Wave System

Operation

Common Problems and Their Solutions

While preparing for mm-wave measurements you may encounter some of
the following problems. Some recommended points to check are listed
below:

Problem

CAUTION: NO IF FOUND

displayed (or very low detected signal levels)

Possible Causes and Solutions

If a microwave test set is connected as well, verify that the test set ACTIVE
LED is off. If it is on, then toggle the test set address.

1. Press [

SYSTEM

] {

HP-IB ADDRESS

} {

TEST SET

2. Enter [

] [

]

3. Enter [

] [

]

If an RF Switch is also used, the SWITCH 0 LED should be on during
mm-wave operation and off during microwave operation.

Problem

Data is grossly incorrect after calibration.

Possible Causes and Solutions

{

FACTORY PRESET

} was pressed and the {

SET Z0

} function (under the CAL

menu) was reset to 50 ohms during a waveguide calibration. RECALL the
correct mm-wave instrument state (Z

=1), then calibrate again.

Содержание 85106D





















































































































































































































































Результаты поиска

Содержание 85106D

Отзывы:

Похожие инструкции для 85106D

Бренды по названию

Популярные бренды

HP 85106D, Руководство пользователя

Результаты поиска

Содержание 85106D

Отзывы:

Похожие инструкции для 85106D

Бренды по названию

Популярные бренды