HP 85106D Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 244

HP 85106D Скачать руководство пользователя страница 59

2-14

HP 85106D mm-Wave System

Operation

Operating Notes

LO Signal Power
Control

LO signal power is controlled using the {

SOURCE #2 POWER

} function. Refer to

Table 2-2 for recommended and expected LO signal power levels.

Table 2-2

Recommended RF and LO Power Levels For All Bands

Operator Check

To perform an operator's check, complete the following:

•

Measure the power levels of the HP 8510C user parameters a1, b1, a2,
and b2.

•

Observe the appropriate levels (listed in Table 2-3 on page 2-16) to be
certain that the system is operating properly.

•

For complete system verification, refer to Chapter 3, “Performance
Verification” in this manual.

CAUTION

Do not increase source #1 power level or connect a device with gain that is
greater than -13 dBm as shown in these measurements. Greater than about
-10 dBm can result in mixer compression errors, and greater than
+27 dBm can damage the first frequency conversion stage. System
specifications apply when the source #1 power is set as listed in Table 2-2 on
page 2-14.

Perform the Operators
Check

The following measurements show approximate RF signal levels incident at
the first frequency conversion stage and given in dBm (even though the
marker value read-out is in dB). During this procedure you may adjust the
RF source #1 power level, this will change the available power at the test
port, and thus the IF signal level.

This measurement is important for setting signal levels in preparation for
measuring components. This is especially true for amplifiers. The maximum
signal applied to Port 2 (or Port 1) without damage depends upon the band,
exc27 dBm can cause damage. If the IF signal level exceeds about
-10 dBm, measurement errors due to compression result.

Frequency
Range

45 MHz - 50 GHz

33 GHz -50 GHz

40 GHz -60 GHz

50 GHz -75 GHz

75 GHz -110 GHz

Frequency

Band

Coaxial

(option001)

Waveguide

Q-band

WR-22

U-band

WR-19

V-band
WR-15

W-band

WR-10

Source #1

(RF) Power

+10

−

20

−

25

−

30

−

20

Source #2

(RF) Power

+3

+3

+3

+3

N/A

«
...
57
58
59
60
61
...
»

Содержание 85106D





















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды